{"title":"Smok Pods","description":"\u003ch1\u003e\u003cspan\u003eSmok Pods\u003c\/span\u003e\u003c\/h1\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003e\u003cstrong\u003eSmok pods\u003c\/strong\u003e are the refillable cartridges behind one of vaping's biggest names, spanning everything from the pocket-sized Novo to the high-powered RPM. Few brands cover as much ground: Smok pods run tight mouth-to-lung setups for anyone off the cigarettes, loose direct-to-lung ones for cloud chasers, and plenty in between. Fill a pod, drop in the coil it takes, and vape, then renew whichever part wears first.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eThat range is Smok's great strength and, for a first-time buyer, its one complication. Because so many pods use a separate, swappable coil, buying the right refill usually means matching two things: the pod to your device, and the coil to your pod. Get both right and the setup is hard to beat for versatility. The full selection of Smok pods and coils sits in the grid below, filterable by device, series, and resistance.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp dir=\"ltr\"\u003e\u003cspan\u003eEvery checkout runs an age check, and Pirate Vapes supplies Smok pods and coils to adults aged 18 and over.\u003c\/span\u003e\u003c\/p\u003e","products":[{"product_id":"smok-novo-2x-pods","title":"SMOK Novo 2X Replacement Pods | Pack Of 3","description":"\u003ch2\u003eSMOK Novo 2X Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eA refillable \u003cstrong\u003e2ml pod\u003c\/strong\u003e with an \u003cstrong\u003eintegrated mesh coil\u003c\/strong\u003e, sold in packs of three. That is the short version. The SMOK Novo 2X pods run a meshed MTL coil behind a top-fill port, giving you a smooth draw that is easy to refill.\u003c\/p\u003e\n\u003cp\u003eTwo mesh resistances in the original range, a magnetic click-in fit, and a clear window to watch your juice level. If your Novo is on its last pod, a fresh three-pack is the cheapest way to bring the flavour back. Browse the full \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/replacement-pods\" target=\"_blank\" title=\"Replacement Pods\" rel=\"noopener\"\u003e\u003cstrong\u003eReplacement Pods\u003c\/strong\u003e\u003c\/a\u003e range to stock up.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eTop-fill beats side-fill. Lift the mouthpiece cover, drip your liquid straight in, done. No fiddling with a plug on the side, which is the part everyone hated about the older Novo pods.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMesh, not a wire coil. Faster to heat, cleaner flavour.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTwo resistances let you nudge the draw warmer or cooler without buying a new device.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic fit. The pod snaps into place and holds, with gold-plated contacts for a steady connection.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eA three-pack is proper value since a pod is a consumable and you will work through them with daily vaping.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSMOK Novo 2X Pod Features\u003c\/h2\u003e\n\u003ch3\u003eTop-Fill Was the Fix Everyone Wanted\u003c\/h3\u003e\n\u003cp\u003eOlder Novo pods filled from the side through a stubborn silicone plug. The \u003cstrong\u003e2X\u003c\/strong\u003e moved the port to the top, under the \u003cstrong\u003emouthpiece cover\u003c\/strong\u003e. Flip the cover, fill, snap it shut. Honestly, it is the single best change to the pod, and it makes refills a ten-second job rather than a mess.\u003c\/p\u003e\n\u003ch3\u003eWhy Does Mesh Matter Here?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eintegrated mesh coil\u003c\/strong\u003e spreads heat across a wider strip than a round wire, so liquid vaporises faster and more evenly. In practice, that means sharper flavour and a coil that holds its taste for longer before it starts to fade. For an \u003cstrong\u003eMTL\u003c\/strong\u003e pod, that is exactly what you want.\u003c\/p\u003e\n\u003ch3\u003eDial the Draw In\u003c\/h3\u003e\n\u003cp\u003eWhile the pod itself uses a fixed dual-airflow inlet design, it works seamlessly with the adjustable airflow sliders found on compatible devices like the Novo 2X kit. Set it on the device to tighten things down for a cigarette-style pull or open it up for a slightly airier draw.\u003c\/p\u003e\n\u003ch3\u003eBuilt for Nic Salts\u003c\/h3\u003e\n\u003cp\u003eThe tight \u003cstrong\u003eMTL\u003c\/strong\u003e draw and mesh coil suit \u003cstrong\u003enic salt\u003c\/strong\u003e e-liquid at UK strengths. Pair the pods with a bottle of \u003cstrong\u003eNic Salts\u003c\/strong\u003e at 10mg or 20mg for the smoothest hit, or a \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/50-50-e-liquids\" target=\"_blank\" title=\"50\/50 E-Liquid\" rel=\"noopener\"\u003e\u003cstrong\u003e50\/50 E-Liquid\u003c\/strong\u003e\u003c\/a\u003e if you prefer freebase.\u003c\/p\u003e\n\u003ch2\u003eSMOK Novo 2X Pod Resistance Options\u003c\/h2\u003e\n\u003cp\u003eTwo mesh options in the original lineup. Both are MTL, both refillable. The choice comes down to how warm you want the draw.\u003c\/p\u003e\n\u003cp\u003eMost popular is the \u003cstrong\u003e0.9ohm\u003c\/strong\u003e. It is the standard Novo 2X pod, a tighter mouth-to-lung draw that pairs beautifully with mid-strength nic salts. If you are not sure which to pick, start here.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003e0.6ohm\u003c\/strong\u003e is the mesh flavour edition. Slightly lower resistance, so a touch warmer with a bit more vapour, while staying firmly in MTL territory. Good if you like your flavour turned up.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.6ohm\u003c\/li\u003e\n\u003cli\u003e0.9ohm\u003cstrong\u003e\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Fill the SMOK Novo 2X Pod\u003c\/h2\u003e\n\u003cp\u003eUnder a minute once you have done it once.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003ePull the pod out of the device. It releases from the magnetic slot with a gentle tug.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLift the mouthpiece cover to reveal the top-fill port.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eDrip your e-liquid in slowly, filling to just under the 2ml line and keeping clear of the central airflow tube.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClose the cover firmly and wipe any excess from the outside.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClick the pod back in and stand it upright for five minutes so the mesh wicks all the way through before your first draw.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTake a couple of soft pulls to start, and if your device has an airflow slider, adjust it to taste.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the SMOK Novo 2X Pod Box\u003c\/h2\u003e\n\u003cp\u003eThree refillable Novo 2X pods in your chosen resistance. That is it. No e-liquid, no device, no coils to install separately since each pod already has its mesh coil built in. You supply the juice and the Novo device.\u003c\/p\u003e\n\u003ch2\u003eFits the Whole SMOK Novo Family\u003c\/h2\u003e\n\u003cp\u003eCompatibility is the strong point here. These pods slot into far more than the 2X device. The original \u003cstrong\u003eNovo\u003c\/strong\u003e and the \u003cstrong\u003eNovo 2\u003c\/strong\u003e take them. So do the \u003cstrong\u003eNovo 2S\u003c\/strong\u003e and \u003cstrong\u003e2C\u003c\/strong\u003e. The \u003cstrong\u003eNovo 3\u003c\/strong\u003e works too, and both the \u003cstrong\u003ePropod\u003c\/strong\u003e and \u003cstrong\u003ePropod GT\u003c\/strong\u003e kits round out the list. If you own more than one Novo, a single pod type covers the lot.\u003c\/p\u003e\n\u003cp\u003eWhat they will not fit is SMOK's other pod platforms like the Nord or RPM ranges, which use a completely different pod. Need a device to match? The \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/refillable-pod-kits\" target=\"_blank\" title=\"Refillable Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eRefillable Pod Kits\u003c\/strong\u003e\u003c\/a\u003e section has options.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK's \u003cstrong\u003eNovo\u003c\/strong\u003e line is one of the most recognised pod platforms in UK vaping, and the \u003cstrong\u003e2X\u003c\/strong\u003e pod is a big part of why. The move to a \u003cstrong\u003etop-fill, mesh-coil design\u003c\/strong\u003e fixed the two things people grumbled about on earlier Novo pods: awkward filling and flat flavour.\u003c\/p\u003e\n\u003cp\u003eThat single pod format now spans nearly the whole Novo range, which is exactly why it stays a reliable, easy-to-restock choice. SMOK builds the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/smok-vapes\" target=\"_blank\" title=\"SMOK Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eSMOK Pod Kits\u003c\/strong\u003e\u003c\/a\u003e these pods live in, so the fit is always spot on.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003eA pod is a running cost, not a one-off. With daily vaping, you will move through a three-pack over a few weeks, sooner with sweeter, darker liquids that gunk the mesh faster. Setting up an Auto Refill through \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e means fresh pods land on your doorstep before you run dry, and you save on every order.\u003c\/p\u003e\n\u003cp\u003eAll stock is \u003cstrong\u003eTPD compliant\u003c\/strong\u003e, checkout is \u003cstrong\u003eage-verified\u003c\/strong\u003e, and it is strictly \u003cstrong\u003eover-18s only\u003c\/strong\u003e. Spend over £40 and delivery is free.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSMOK Novo 2X pods\u003c\/strong\u003e are the easy, sensible refill for anyone running a Novo device. \u003cstrong\u003eTop-fill, mesh coil, two resistances\u003c\/strong\u003e and a fit that covers most of the Novo family in one pod.\u003c\/p\u003e\n\u003cp\u003eKeep a pack or two spare, pair them with the right nic salt, and your device keeps performing like new. Browse more \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e or pick up a three-pack today at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich devices do the 2X pods fit?\u003c\/h3\u003e\n\u003cp\u003eMost of the Novo family. The original Novo, Novo 2, 2S, 2C, Novo 3, plus the Propod and Propod GT kits. They do not fit the Nord or RPM ranges.\u003c\/p\u003e\n\u003ch3\u003eAre Novo 2X pods refillable or prefilled?\u003c\/h3\u003e\n\u003cp\u003eRefillable. You add your own e-liquid through the top port. No juice comes in the box.\u003c\/p\u003e\n\u003ch3\u003eWhich Novo 2X pod resistance should I get?\u003c\/h3\u003e\n\u003cp\u003eThe 0.9ohm for a standard MTL draw, the 0.8ohm if you want it a touch warmer with more flavour. Both suit nic salts.\u003c\/p\u003e\n\u003ch3\u003eWhat e-liquid works best in Novo 2X pods?\u003c\/h3\u003e\n\u003cp\u003eNic salts at 10mg or 20mg, or a 50\/50 freebase. High-VG juice is too thick for these MTL pods and can cause dry hits.\u003c\/p\u003e\n\u003ch3\u003eHow long does a Novo 2X pod last?\u003c\/h3\u003e\n\u003cp\u003eUsually one to two weeks each with daily use. Darker and sweeter liquids shorten that as residue builds on the mesh. A three-pack keeps you covered for a good stretch.\u003c\/p\u003e\n\u003ch3\u003eCan I just rinse and reuse a Novo 2X pod?\u003c\/h3\u003e\n\u003cp\u003eNot really. The coil is built in, so once the flavour drops off or it starts tasting burnt, swap in a fresh pod rather than trying to revive it.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"0.6 Ohm","offer_id":52722990121242,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true},{"title":"0.9 Ohm","offer_id":52722990154010,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/SMOK_Novo_2X_Replacement_Pods.jpg?v=1787223462"},{"product_id":"smok-morph-80-replacement-lp2-pods","title":"SMOK Morph 80 Replacement LP2 Pods | Pack Of 3","description":"\u003ch2\u003eSMOK Morph 80 Replacement LP2 Pods\u003c\/h2\u003e\n\u003cp\u003eA \u003cstrong\u003e2ml refillable pod\u003c\/strong\u003e that brings your \u003cstrong\u003eSMOK Morph Pod-80\u003c\/strong\u003e back to life when the original starts to leak or lose flavour. Sold as a \u003cstrong\u003epack of three\u003c\/strong\u003e, the \u003cstrong\u003eLP2 replacement pod\u003c\/strong\u003e clicks straight onto the \u003cstrong\u003eMorph 80\u003c\/strong\u003e and \u003cstrong\u003eMorph S Pod-80\u003c\/strong\u003e, held firm by \u003cstrong\u003estrong magnets\u003c\/strong\u003e and filled from the top through a \u003cstrong\u003esilicone-stoppered port\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt runs the full \u003cstrong\u003eSMOK LP2 mesh coil\u003c\/strong\u003e range for a warm \u003cstrong\u003edirect-to-lung\u003c\/strong\u003e draw, so load it with a high-VG juice and you are back in business. Coils are sold separately. Made for the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/refillable-pod-kits\" target=\"_blank\" title=\"Refillable Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eRefillable Pod Kits\u003c\/strong\u003e\u003c\/a\u003e crowd who refill rather than replace.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eIt is a clean, exact swap for a Morph Pod-80 pod that has cracked, clouded or started weeping around the base, and it seats with the same reassuring magnetic snap as the original.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTop-fill through a silicone stopper means refills take seconds and stay tidy.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eRuns the whole LP2 mesh range, so you choose the resistance that suits your draw rather than being stuck with one.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eThree per pack. Pods are wear parts, and a spare or two on the shelf saves a dead night.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic hold keeps it locked to the device through pocket knocks and daily handling.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSMOK Morph 80 LP2 Pod Features\u003c\/h2\u003e\n\u003ch3\u003eTwo Millilitres, Filled From the Top\u003c\/h3\u003e\n\u003cp\u003eThe pod holds \u003cstrong\u003e2ml\u003c\/strong\u003e in line with UK rules, and the \u003cstrong\u003etop-fill\u003c\/strong\u003e design is the part you will appreciate daily. A soft \u003cstrong\u003esilicone stopper\u003c\/strong\u003e lifts to reveal the fill port, so you refill without pulling the pod off the device or fighting a fiddly bung. Quick, clean, no mess down the side.\u003c\/p\u003e\n\u003ch3\u003eWhy Do the Magnets Matter?\u003c\/h3\u003e\n\u003cp\u003eBecause a pod that shifts in its housing leaks and loses flavour. SMOK holds the LP2 pod to the \u003cstrong\u003eMorph Pod-80\u003c\/strong\u003e with \u003cstrong\u003estrong magnets\u003c\/strong\u003e rather than a friction fit, so it drops in, clicks, and stays put. No wobble, no gaps for air to sneak past. It just sits where it should.\u003c\/p\u003e\n\u003ch3\u003eThe LP2 Mesh Platform\u003c\/h3\u003e\n\u003cp\u003eThis pod is built around SMOK's \u003cstrong\u003eLP2 mesh coil\u003c\/strong\u003e system, a \u003cstrong\u003esub-ohm\u003c\/strong\u003e platform tuned for \u003cstrong\u003edirect-to-lung\u003c\/strong\u003e clouds. Mesh spreads the heat over a wider surface, which wicks faster and keeps flavour sharper than an old-style wire coil. Stock spares from the wider \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Replacement Vape Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eReplacement Vape Coils\u003c\/strong\u003e\u003c\/a\u003e range so you are never caught short.\u003c\/p\u003e\n\u003ch3\u003eMatch It to a High-VG Juice\u003c\/h3\u003e\n\u003cp\u003eThe LP2 mesh DL coils want a thicker liquid. Aim for \u003cstrong\u003e70% VG or higher\u003c\/strong\u003e for the smoothest wicking and the best cloud on the 0.23ohm coil. However, if you opt for the \u003cstrong\u003e0.6ohm DC coil\u003c\/strong\u003e, a 50\/50 blend or nic salt is the perfect match for its MTL draw. Browse the e-liquid shelves to pair your juice to your chosen coil.\u003c\/p\u003e\n\u003ch3\u003eBuilt as a Wear Part\u003c\/h3\u003e\n\u003cp\u003eNo pod lasts forever. The plastic clouds, the seals soften, and eventually flavour drops off. That is normal, and it is exactly why these come in a \u003cstrong\u003ethree-pack\u003c\/strong\u003e. Keep one in rotation and the others in the drawer, and a tired pod is a two-minute fix rather than a lost evening.\u003c\/p\u003e\n\u003ch2\u003eSMOK Morph 80 LP2 Coil Options\u003c\/h2\u003e\n\u003cp\u003eThe pod ships empty, so you choose the LP2 coil to match your style. The range is cross-compatible across SMOK's \u003cstrong\u003eLP2 pods\u003c\/strong\u003e, giving you both \u003cstrong\u003eDTL and MTL options\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eMost popular is the \u003cstrong\u003e0.23ohm mesh\u003c\/strong\u003e. It leans into warmer, denser vapour and suits anyone who wants the fuller sub-ohm hit the Morph 80 was built for.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003e0.6ohm DC\u003c\/strong\u003e is the tighter, cooler MTL option. It sips less liquid and less battery, which makes it the sensible pick if you want your juice and charge to stretch further, or prefer a restricted mouth-to-lung pull.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.23ohm Mesh\u003c\/li\u003e\n\u003cli\u003e0.6ohm DC\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Fit and Fill the SMOK Morph 80 LP2 Pod\u003c\/h2\u003e\n\u003cp\u003eQuick job. A few minutes, most of it just waiting.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003ePress a fresh LP2 coil firmly into the base of the pod until it clicks home.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eAdd three or four drops of e-liquid straight onto the exposed cotton of the new coil.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLift the silicone stopper on the top and fill the pod with a high-VG juice, keeping clear of the central airflow tube.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClose the stopper and snap the pod onto the Morph 80, letting the magnets pull it into place.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStand it upright and leave it be for five to seven minutes so the mesh drinks its fill before any power reaches it. Rushing this is how coils get scorched on the first pull.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTake two or three gentle draws to settle the wick, then vape as normal.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the SMOK Morph 80 LP2 Pod Box\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eThree empty LP2 replacement pods\u003c\/strong\u003e, and that is it. No \u003cstrong\u003ecoils\u003c\/strong\u003e, no e-liquid and no device are included, so you supply an LP2 coil and a bottle of juice to get going. Pirate Vapes stocks both alongside the pods, so a full refill kit lands in a single order.\u003c\/p\u003e\n\u003ch2\u003eFits the Morph Pod-80 Family, Nothing Else\u003c\/h2\u003e\n\u003cp\u003eThese pods are cut specifically for the \u003cstrong\u003eSMOK Morph Pod-80\u003c\/strong\u003e and the \u003cstrong\u003eMorph S Pod-80\u003c\/strong\u003e. If you run either of those, this is your pod.\u003c\/p\u003e\n\u003cp\u003eThey will not fit SMOK's other pod systems. Not the RPM series. Not the Nord line. Those use entirely different pod shapes and coil platforms, so a mismatch simply will not seat. When in doubt, check the pod currently in your device says LP2, then browse the wider \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/smok-vapes\" target=\"_blank\" title=\"SMOK Range\" rel=\"noopener\"\u003e\u003cstrong\u003eSMOK Range\u003c\/strong\u003e\u003c\/a\u003e for anything else you need.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK has spent well over a decade as one of the biggest names in UK sub-ohm vaping, and the LP2 platform is a good example of why. Rather than reinventing the pod with every device, SMOK built the LP2 as a shared standard across several of its kits, so a single coil and pod format carries between them.\u003c\/p\u003e\n\u003cp\u003eThe Morph Pod-80 leans on that: a magnetic, top-fill pod with fast-wicking mesh coils, designed to be refilled and replaced cheaply rather than binned in one piece.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods wear out on a schedule, so it pays to buy ahead. With \u003cstrong\u003ethree in a pack\u003c\/strong\u003e, most vapers keep one on the device and rotate the spares in every few weeks as flavour fades. Pair a pack with a couple of \u003cstrong\u003eLP2 coils\u003c\/strong\u003e and a high-VG bottle and you have months of vaping sorted.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e dispatches every order the same day when it is placed before 4pm, packed to arrive intact. \u003cstrong\u003eAge-verified checkout\u003c\/strong\u003e, over-18s only, and all hardware is TPD compliant. Free Pirate Post kicks in over £25.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSMOK Morph 80 LP2 pods\u003c\/strong\u003e are the simple, correct fix for a Morph Pod-80 that has started to tire. A \u003cstrong\u003e2ml top-fill pod\u003c\/strong\u003e, magnetic and mess-free, built around SMOK's proven \u003cstrong\u003eLP2 mesh coils\u003c\/strong\u003e for a warm DTL draw.\u003c\/p\u003e\n\u003cp\u003eAdd the coil and juice to suit your taste, keep the spares handy, and your device feels new again. Grab a pack alongside coils and \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eDoes the Morph 80 pod come with coils?\u003c\/h3\u003e\n\u003cp\u003eNo. The pack is three empty pods only. You add an LP2 coil and your own e-liquid.\u003c\/p\u003e\n\u003ch3\u003eWhich coils fit these pods?\u003c\/h3\u003e\n\u003cp\u003eThe SMOK LP2 range, commonly in 0.23ohm Mesh and 0.6ohm DC. The 0.23ohm gives a warm DTL draw, while the 0.6ohm provides a tighter MTL pull.\u003c\/p\u003e\n\u003ch3\u003eWhat devices do they work with?\u003c\/h3\u003e\n\u003cp\u003eOnly the SMOK Morph Pod-80 and Morph S Pod-80. They will not fit RPM, Nord or other SMOK pod systems.\u003c\/p\u003e\n\u003ch3\u003eHow much does the pod hold?\u003c\/h3\u003e\n\u003cp\u003e2ml, the UK limit. Fill it from the top by lifting the silicone stopper. No need to remove the pod first.\u003c\/p\u003e\n\u003ch3\u003eWhat e-liquid should I use?\u003c\/h3\u003e\n\u003cp\u003eIf using the 0.23ohm Mesh coil, a high-VG juice (70% VG or thicker) is best. If you run the 0.6ohm DC coil, a 50\/50 e-liquid or nic salt is ideal.\u003c\/p\u003e\n\u003ch3\u003eHow long does a pod last before it needs replacing?\u003c\/h3\u003e\n\u003cp\u003eIt varies with use, but a few weeks is typical before the plastic clouds or flavour dulls. That is why they come three to a pack.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"Default Title","offer_id":52723954614554,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/SMOK_Morph_80_Replacement_LP2_Pods.jpg?v=1787232969"},{"product_id":"smok-rpm-85-and-rpm-100-pods","title":"SMOK RPM 85 and RPM 100 Replacement Pods","description":"\u003ch2\u003eSMOK RPM 85 and RPM 100 Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eTwo pod versions, one job: keeping your \u003cstrong\u003eSMOK RPM 85\u003c\/strong\u003e or \u003cstrong\u003eSMOK RPM 100\u003c\/strong\u003e running without buying a whole new kit. These are the \u003cstrong\u003e2ml TPD refillable pods\u003c\/strong\u003e for both devices, sold in a \u003cstrong\u003epack of 3\u003c\/strong\u003e, and you choose the fitment that matches your coils. The \u003cstrong\u003eRPM 3 pod\u003c\/strong\u003e takes SMOK's RPM 3 mesh coils for airier sub-ohm draws.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eRPM 2 pod\u003c\/strong\u003e runs the wider RPM 2 range for a tighter pull. Top-fill, magnetic seating, clear body so you can watch your level drop. Coils are sold separately, so keep a couple of spare \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/replacement-pods\" target=\"_blank\" title=\"Replacement Pods\" rel=\"noopener\"\u003e\u003cstrong\u003eReplacement Pods\u003c\/strong\u003e\u003c\/a\u003e in the drawer.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eTwo fitments, one device. Whether you run the punchy RPM 3 mesh for clouds or the more flexible RPM 2 range for a tighter draw, there is a pod here that fits the RPM 85 and the RPM 100 without any adapters or workarounds.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e2ml top-fill means you slide, drip, and go. No pulling the pod off the mod every refill.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic seating drops the pod in and holds it firm, so it does not creep loose in a pocket.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eA locking coil base keeps the coil seated and the liquid where it belongs.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSold in threes. One in use, two in reserve.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSMOK RPM 85 and RPM 100 Replacement Pods Features\u003c\/h2\u003e\n\u003ch3\u003ePick the Pod That Matches Your Coils\u003c\/h3\u003e\n\u003cp\u003eThis is the only choice that matters. The \u003cstrong\u003eRPM 3 pod\u003c\/strong\u003e accepts SMOK's RPM 3 mesh coils for warm, open sub-ohm vaping around 40 to 80W. The \u003cstrong\u003eRPM 2 pod\u003c\/strong\u003e takes the broader RPM 2 range, from low-ohm mesh up to a 0.6 DC head for a tighter pull. Fit the pod to your coils, and you cover everything from airy clouds to a snugger draw, which is why they suit vapers stepping across \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/refillable-pod-kits\" target=\"_blank\" title=\"Refillable Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eRefillable Pod Kits\u003c\/strong\u003e\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eWhy Bother With Top-Fill?\u003c\/h3\u003e\n\u003cp\u003eBecause it is faster and cleaner. Slide the cap across, drip your liquid into the port, close it. The pod stays on the device the whole time. No unscrewing, no juice on your fingers, no fishing around under a tank base. Honestly, once you have used a \u003cstrong\u003esliding top cap\u003c\/strong\u003e, going back feels like a chore.\u003c\/p\u003e\n\u003ch3\u003eThe Locking Base That Stops the Wobble\u003c\/h3\u003e\n\u003cp\u003ePush-to-fit coils are quick, but a loose coil leaks and tastes flat. SMOK's \u003cstrong\u003elocking base\u003c\/strong\u003e clamps the coil in place so it stays put and seals the join at the same time. It also means the coil cannot be tugged out by accident, which is a bit of quiet reassurance if there are curious hands about the house.\u003c\/p\u003e\n\u003ch3\u003eSnap It On and Go\u003c\/h3\u003e\n\u003cp\u003eThe pod holds to the mod with \u003cstrong\u003emagnets\u003c\/strong\u003e rather than a clip, so seating it is a one-handed job. Pull it off to refill or swap versions, drop it back, and the contacts line up on their own. Small thing, but it is the sort of detail you notice every single day.\u003c\/p\u003e\n\u003ch3\u003eAirflow You Can Actually Dial In\u003c\/h3\u003e\n\u003cp\u003eThese pods work seamlessly with the \u003cstrong\u003eadjustable airflow ring\u003c\/strong\u003e built into the top of your RPM 85 or RPM 100 device. Simply twist the dial on the mod to tune your draw from restricted to fully open without changing coils. Pair that with the clear pod body, and you always know two things at a glance: how tight your airflow is set and how much liquid you have left.\u003c\/p\u003e\n\u003ch2\u003eSMOK RPM 85 and RPM 100 Replacement Pods Options\u003c\/h2\u003e\n\u003cp\u003eThere are two versions in the range, and they are not interchangeable once a coil is in. The right pick is decided by the coils you own, not by looks, since both share the same shell and the same \u003cstrong\u003e2ml\u003c\/strong\u003e well.\u003c\/p\u003e\n\u003cp\u003eMost vapers land on the \u003cstrong\u003eRPM 3 pod\u003c\/strong\u003e first, because both kits ship with RPM 3 coils in the box. It is built for airier direct-to-lung vaping and drinks thick juice, so pair it with 70VG sub-ohm liquid from the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/70-30-shortfills\" target=\"_blank\" title=\"70-30 Shortfills\" rel=\"noopener\"\u003e\u003cstrong\u003e70-30 Shortfills\u003c\/strong\u003e\u003c\/a\u003e range at around 3 to 6mg.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eRPM 2 pod\u003c\/strong\u003e is the one to grab if you prefer a firmer draw or already have RPM 2 coils. Fit a higher-resistance head like the 0.6 DC, and it leans towards a restricted, cooler pull that works nicely with \u003cstrong\u003eNic Salts\u003c\/strong\u003e or a balanced 50\/50.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM 3 pod\u003c\/li\u003e\n\u003cli\u003eRPM 2 pod\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Set Up the SMOK RPM 85 and RPM 100 Pods\u003c\/h2\u003e\n\u003cp\u003eUnder two minutes, coil included.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003ePush your chosen coil up into the base of the pod until it clicks, and the lock engages.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSlide the top cap open and put 2 to 3 drops of e-liquid straight onto the exposed cotton first.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFill with e-liquid to just below the max line, then slide the cap shut.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSeat the pod on the mod. The magnets pull it square on their own.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStand the device upright and leave it a full seven minutes so the wick draws liquid all the way through before you fire it.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStart low and build up. Take a few gentle pulls, then climb to your coil's wattage.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the SMOK RPM 85 and RPM 100 Pods Box\u003c\/h2\u003e\n\u003cp\u003eThree empty pods in your chosen fitment, either the \u003cstrong\u003eRPM 2\u003c\/strong\u003e or the \u003cstrong\u003eRPM 3\u003c\/strong\u003e version. That is the lot. No coils, no e-liquid, and no device. These are spares for a kit you already own, so anything you need to actually vape gets added separately.\u003c\/p\u003e\n\u003ch2\u003eBuilt for the RPM 85 and RPM 100, and Nothing Else\u003c\/h2\u003e\n\u003cp\u003eThese pods seat in two devices only: the \u003cstrong\u003eSMOK RPM 85\u003c\/strong\u003e and the \u003cstrong\u003eSMOK RPM 100\u003c\/strong\u003e. They will not fit the older RPM or RPM 2 kits. They are not Nord pods either. The part people trip on is the coil match.\u003c\/p\u003e\n\u003cp\u003eAn \u003cstrong\u003eRPM 3 pod\u003c\/strong\u003e takes RPM 3 coils. An \u003cstrong\u003eRPM 2 pod\u003c\/strong\u003e takes the RPM 2 range. Cross the two and the coil simply will not lock in. Grab your \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Vape Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Coils\u003c\/strong\u003e\u003c\/a\u003e to suit, and Pirate Vapes keeps the SMOK line grouped so you are not hunting across the site.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK, run by Shenzhen IVPS, has been one of the loudest names in sub-ohm hardware for well over a decade. The \u003cstrong\u003eRPM\u003c\/strong\u003e family is where the brand folded pod convenience and mod-level power into a single shell. The \u003cstrong\u003eRPM 85\u003c\/strong\u003e and \u003cstrong\u003eRPM 100\u003c\/strong\u003e are the current standard-bearers of that idea: real wattage, a colour screen, swappable coils behind a refillable pod.\u003c\/p\u003e\n\u003cp\u003eThese pods are the part that wears with use, so keeping \u003cstrong\u003egenuine SMOK spares\u003c\/strong\u003e to hand is the cheapest way to keep either kit tasting the way it should.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods outlast coils, but they do not last forever. Seals soften, the plastic clouds up, and flavour dulls off the back of it. A \u003cstrong\u003epack of 3\u003c\/strong\u003e lets you rotate a fresh one in before that point and hold a spare for the version you are not currently running.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e dispatches every order the same day before 4 pm in padded packaging. All stock is \u003cstrong\u003eTPD compliant\u003c\/strong\u003e, checkout is \u003cstrong\u003eage-verified\u003c\/strong\u003e, and sales are \u003cstrong\u003eover-18s only\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eIf you own an \u003cstrong\u003eRPM 85\u003c\/strong\u003e or \u003cstrong\u003eRPM 100\u003c\/strong\u003e, a spare three-pack is one of those quiet buys you will be glad of the next time a pod gives out mid-week. Choose the fitment that matches your coils, keep the box topped up, and the kit carries on earning its place.\u003c\/p\u003e\n\u003cp\u003ePair them with fresh \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e and browse the full hardware range at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich pod do I need for my kit?\u003c\/h3\u003e\n\u003cp\u003eGo by your coils. RPM 3 coils need the RPM 3 pod. RPM 2 coils need the RPM 2 pod. Both versions fit the RPM 85 and the RPM 100 without any bother.\u003c\/p\u003e\n\u003ch3\u003eDo RPM 85 and RPM 100 pods come with coils?\u003c\/h3\u003e\n\u003cp\u003eNo. Coils are sold separately, so add the RPM 2 or RPM 3 heads to match your chosen pod.\u003c\/p\u003e\n\u003ch3\u003eHow much do the RPM 85 and RPM 100 pods hold?\u003c\/h3\u003e\n\u003cp\u003e2ml, in line with UK TPD rules. A larger 6ml version exists in some overseas markets, but the pods sold here are the 2ml UK spec.\u003c\/p\u003e\n\u003ch3\u003eWhat e-liquid works best with the RPM 85 and RPM 100 pods?\u003c\/h3\u003e\n\u003cp\u003eFor the RPM 3 pod, reach for 70VG shortfills at 3 to 6mg. If you fit a higher-ohm coil in the RPM 2 pod for a tighter draw, switch to a 50\/50 or a nic salt instead.\u003c\/p\u003e\n\u003ch3\u003eWhy is my RPM 85 and RPM 100 pod leaking?\u003c\/h3\u003e\n\u003cp\u003eUsually the coil is not fully locked in, or the pod was overfilled. Push the coil up until it clicks and fill to just below the max line, not over it.\u003c\/p\u003e\n\u003ch3\u003eHow long does a RPM 85 and RPM 100 pod last?\u003c\/h3\u003e\n\u003cp\u003eWeeks, not days. Most vapers swap the pod itself every one to three weeks, while the coil inside gets changed more often.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"RPM 2 Pod","offer_id":52736937132314,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RPM 3 Pod","offer_id":52736937165082,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/SMOK_RPM_85_and_RPM_100_Replacement_Pods.jpg?v=1787576028"},{"product_id":"smok-alike-rpm-nord-replacement-pod","title":"Smok Alike RPM Nord Replacement Pod","description":"\u003ch2\u003eSmok Alike RPM Nord Replacement Pod\u003c\/h2\u003e\n\u003cp\u003eTwo coil platforms, one device. The \u003cstrong\u003eSmok Alike RPM Nord Replacement Pod\u003c\/strong\u003e is the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/replacement-pods\" target=\"_blank\" title=\"Replacement Pod\" rel=\"noopener\"\u003e\u003cstrong\u003eReplacement Pod\u003c\/strong\u003e\u003c\/a\u003e built for the SMOK Alike, and it comes in two versions depending on which coil family you run: \u003cstrong\u003eRPM\u003c\/strong\u003e or \u003cstrong\u003eNord\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eBoth fill to \u003cstrong\u003e2ml\u003c\/strong\u003e at the UK TPD line through a \u003cstrong\u003eside-fill port\u003c\/strong\u003e with a silicone plug, so there is no popping the pod apart to top it up. Pirate Vapes stocks both versions. TPD compliant. Over 18s only. Pick the version that matches your Alike setup.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eTwo pod types in one product, so whichever coil family your Alike kit runs, there is a matching pod\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSide-fill port with a secure silicone stopper makes top-ups quick and mess-free without fiddling with bottom caps\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eCompatible with the full RPM coil range and the full Nord coil range, not locked to one resistance\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eReplace just the pod, not the whole kit, when a seal starts to wear or the shell clouds up\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStraightforward 2ml capacity that keeps things TPD compliant without any workarounds\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSmok Alike RPM Nord Replacement Pod Features\u003c\/h2\u003e\n\u003ch3\u003eTwo Platforms, Correctly Separated\u003c\/h3\u003e\n\u003cp\u003eRPM and Nord coils do not interchange. Different base, different seating, different resistance range entirely. Rather than force one universal pod onto both, SMOK built this as two distinct pod types so each coil family gets a pod actually engineered around it, whether you run yours for tight \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/mtl-vape-kits\" target=\"_blank\" title=\"MTL Vape Kit\" rel=\"noopener\"\u003e\u003cstrong\u003eMTL Vape Kit\u003c\/strong\u003e\u003c\/a\u003e style draws or something looser. Order the wrong one, and it simply won't work, so check your existing pod before buying.\u003c\/p\u003e\n\u003ch3\u003eSide-Fill Is Just Faster\u003c\/h3\u003e\n\u003cp\u003ePull the silicone plug, tip liquid in, push it back. That is the whole refill process. No unscrewing the base, no bottom-fill fiddling, no risk of e-liquid running down your hands while you try to line up a fill port that is facing the wrong way. \u003cstrong\u003eQuick top-ups during the day, genuinely quick.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch3\u003eRuns the Whole RPM and Nord Coil Ranges\u003c\/h3\u003e\n\u003cp\u003eThis is not a pod locked to one resistance. The \u003cstrong\u003eRPM version\u003c\/strong\u003e takes anything from RPM's mesh coils through to its MTL and DC options, and the \u003cstrong\u003eNord version\u003c\/strong\u003e does the same across the Nord coil family. Fair enough, that means a bit of research on which coil suits your vaping style, but it also means the pod itself never becomes the bottleneck.\u003c\/p\u003e\n\u003ch3\u003ePod Wears Out Before the Kit Does\u003c\/h3\u003e\n\u003cp\u003eRealistically, the pod shell is the part that shows age first. Scratches, a bit of cloudiness, maybe a seal that is not quite as tight as it used to be. \u003cstrong\u003eReplacing the pod on its own\u003c\/strong\u003e keeps the rest of the Alike kit in service without buying a whole new device over one worn part.\u003c\/p\u003e\n\u003ch3\u003eBuilt to Match the Alike's Two-Track Design\u003c\/h3\u003e\n\u003cp\u003eSMOK designed the Alike to run either coil family depending on what the owner prefers, and this replacement pod follows that same logic. \u003cstrong\u003eOne kit, two coil ecosystems, and a pod for each\u003c\/strong\u003e rather than a compromise that half-fits both.\u003c\/p\u003e\n\u003ch2\u003eSmok Alike RPM Nord Replacement Pod Types\u003c\/h2\u003e\n\u003cp\u003eTwo versions available. Match it to the coil family already in your Alike kit, not the other way round.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e2ML NORD\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e2ML RPM\u003c\/li\u003e\n\u003cli\u003e5.5ML RPM\u003c\/li\u003e\n\u003cli\u003e5.8ML NORD\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot sure which one your Alike uses? Check the coil currently seated in your pod. If it says \u003cstrong\u003eRPM\u003c\/strong\u003e, order the RPM pod. If it says \u003cstrong\u003eNord\u003c\/strong\u003e, order the Nord pod.\u003c\/p\u003e\n\u003ch2\u003eHow to Fill the Smok Alike RPM Nord Replacement Pod\u003c\/h2\u003e\n\u003cp\u003eQuick process. Under a minute once you have done it once.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eTake the empty pod out of your Alike device.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFit your chosen RPM or Nord coil into the base, pressing until it seats firmly.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePull the silicone plug on the side of the pod to open the fill port.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFill with your e-liquid up to the marked line, keeping clear of the central airflow tube.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the silicone plug back in firmly until it sits flush.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eIf the coil is new, leave it to saturate for 5 to 10 minutes before your first draw. Skip this, and you risk a dry, burnt hit.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the Smok Alike RPM Nord Replacement Pod Box\u003c\/h2\u003e\n\u003cp\u003eOne replacement pod, in your selected RPM or Nord version. \u003cstrong\u003eNo coil included, no device, no e-liquid.\u003c\/strong\u003e Coils are sold separately to match whichever resistance you want to run.\u003c\/p\u003e\n\u003ch2\u003eBuilt Specifically for the SMOK Alike Pod System\u003c\/h2\u003e\n\u003cp\u003eThis pod is made for one device: the \u003cstrong\u003eSMOK Alike\u003c\/strong\u003e. Match the pod version to the coil platform you are already running, and it clicks straight in. Every version sold here is \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/tpd-compliant-vapes\" target=\"_blank\" title=\"TPD Compliant\" rel=\"noopener\"\u003e\u003cstrong\u003eTPD Compliant\u003c\/strong\u003e\u003c\/a\u003e at the 2ml fill line.\u003c\/p\u003e\n\u003cp\u003eWhat it does not fit: any other SMOK pod kit outside the Alike range. Nord and RPM coils turn up across several SMOK devices, but the pod shell itself is \u003cstrong\u003eAlike-specific\u003c\/strong\u003e. Check our \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-pods\" target=\"_blank\" title=\"Vape Pods\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Pods\u003c\/strong\u003e\u003c\/a\u003e collection if you need a pod for a different SMOK device.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK built both the \u003cstrong\u003eRPM and Nord coil platforms\u003c\/strong\u003e into genuinely long-running product lines, and the Alike brings them together in one kit rather than forcing a choice between them. That is a fairly unusual approach.\u003c\/p\u003e\n\u003cp\u003eMost manufacturers commit to one coil ecosystem per device and stay there. SMOK's decision to support both through this single replacement pod line gives Alike owners more flexibility on coil choice than most comparable kits offer.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods do not last forever, especially with daily refills through the side port. Keeping a spare from our Refills \u0026amp; Pods range in the right version means a worn seal or a cracked shell never puts your Alike out of action.\u003c\/p\u003e\n\u003cp\u003eEvery order from \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e ships same-day before 4 pm, with an age-verified checkout and full TPD compliance across the range. Over-18s only. Spend over £40 and delivery is free with Free Pirate Post.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSmok Alike RPM Nord Replacement Pod\u003c\/strong\u003e does exactly what it says: a proper, correctly matched refill pod for whichever coil platform your Alike runs. \u003cstrong\u003eSide-fill for speed, 2ml TPD-compliant capacity\u003c\/strong\u003e, and full compatibility across both the RPM and Nord coil ranges.\u003c\/p\u003e\n\u003cp\u003eIf your current pod has seen better days, or you're switching coil families, this is the straightforward replacement. Browse \u003cstrong\u003eSMOK\u003c\/strong\u003e coils and kits, check our \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e collection, or head back to \u003ca href=\"https:\/\/piratevapes.co.uk\/\" target=\"_blank\" title=\"Pirate Vapes\" rel=\"noopener\"\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e\u003c\/a\u003e for everything else.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich pod version do I need?\u003c\/h3\u003e\n\u003cp\u003eDepends on your coil. RPM coil currently fitted means the RPM pod. Nord coil means the Nord pod.\u003c\/p\u003e\n\u003ch3\u003eWhat is the e-liquid capacity?\u003c\/h3\u003e\n\u003cp\u003e2ml, in line with UK TPD rules. Some international listings show larger 5.5ml or 5.8ml shell capacities, but UK stock fills to 2ml.\u003c\/p\u003e\n\u003ch3\u003eDoes it come with a coil?\u003c\/h3\u003e\n\u003cp\u003eNo. Coils are sold separately, so you can pick the exact resistance you want.\u003c\/p\u003e\n\u003ch3\u003eCan I use nic salts in this pod?\u003c\/h3\u003e\n\u003cp\u003eYes. Both the RPM and Nord coil ranges work with nic salts and standard freebase e-liquid.\u003c\/p\u003e\n\u003ch3\u003eHow many pods come in a pack?\u003c\/h3\u003e\n\u003cp\u003eThese are sold individually as single replacement pods, so you can buy just the quantity you need.\u003c\/p\u003e\n\u003ch3\u003eHow long does a pod usually last?\u003c\/h3\u003e\n\u003cp\u003eSeveral weeks with normal use, longer if you are gentle with the fill port. Cracks or a loose seal are the usual signs it needs replacing.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"2ML NORD","offer_id":52741497618714,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true},{"title":"2ML RPM","offer_id":52741497651482,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true},{"title":"5.5ML RPM","offer_id":52741497684250,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true},{"title":"5.8ML NORD","offer_id":52741497717018,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/Smok_Alike_RPM_Nord_Replacement_Pod.jpg?v=1787676446"},{"product_id":"smok-rpm-25w-replacement-pods","title":"SMOK RPM 25W Replacement Pods","description":"\u003ch2\u003eSMOK RPM 25W Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eA \u003cstrong\u003e2ml\u003c\/strong\u003e refillable cartridge built for one device and one device only: the \u003cstrong\u003eSMOK RPM 25W\u003c\/strong\u003e pod kit. This is the empty pod, not a prefilled one, so you drop in an \u003cstrong\u003eLP1 coil\u003c\/strong\u003e, fill it with your own e-liquid, and go. The clear \u003cstrong\u003ePCTG\u003c\/strong\u003e shell lets you watch your liquid level drop, a side port with a \u003cstrong\u003esilicone bung\u003c\/strong\u003e handles refills, and the pod clicks onto the device with magnets.\u003c\/p\u003e\n\u003cp\u003eCoils are sold separately. If your original cartridge has clouded, cracked, or started to weep at the seams, a fresh three-pack is the cheap fix. Browse more \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/replacement-pods\" title=\"Replacement Pods\" target=\"_blank\"\u003e\u003cstrong\u003eReplacement Pods\u003c\/strong\u003e\u003c\/a\u003e if you run other kits too.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eA genuine 2ml refillable means you top up with any 50\/50 or nic salt you fancy instead of paying prefilled-pod prices every couple of days, and over a month that gap in cost is not small.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eThe clear PCTG body shows your liquid level at a glance, so you refill before a dry hit wrecks the coil rather than after.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic fitment clicks on and off in a second, with no threads to cross.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePress-fit LP1 coils drop straight into the base, and because the coil is separate, you can change draw style without buying a new pod.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eAdjustable airflow built into the pod lets you tune from a tight MTL pull to something a touch airier, handy when you are stepping down nicotine strength.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSMOK RPM 25W Replacement Pod Features\u003c\/h2\u003e\n\u003ch3\u003eThe Pod Holds 2ml. That Is the UK Limit.\u003c\/h3\u003e\n\u003cp\u003eEvery refillable pod sold here caps at \u003cstrong\u003e2ml\u003c\/strong\u003e, and this one is no exception. That is the legal ceiling for UK cartridges, so do not expect a bigger tank hiding anywhere. What you get instead is a compact pod that tops up in seconds. For a daily MTL vaper, 2ml of \u003cstrong\u003enic salt\u003c\/strong\u003e is roughly a day's worth.\u003c\/p\u003e\n\u003ch3\u003eRunning Low? You Will See It Coming.\u003c\/h3\u003e\n\u003cp\u003eThe shell is moulded from \u003cstrong\u003ePCTG\u003c\/strong\u003e, a semi-clear plastic that lets light through. You can read how much liquid is left without pulling the pod off the device. Thing is, dry firing an \u003cstrong\u003eLP1 coil\u003c\/strong\u003e kills it quickly, so being able to glance down and refill in time genuinely saves you money on coils.\u003c\/p\u003e\n\u003ch3\u003eA Simple Side Fill With a Silicone Bung\u003c\/h3\u003e\n\u003cp\u003eRefilling is a side job, not a top job. Ease back the \u003cstrong\u003esilicone bung\u003c\/strong\u003e on the flank of the pod, angle your nozzle in, and fill to just under the line. Keep clear of the central airflow tube. Then push the bung back until it seats flush. Most leaks people pin on the pod are really a bung left half-open.\u003c\/p\u003e\n\u003ch3\u003eMatch It With the Right LP1 Coil\u003c\/h3\u003e\n\u003cp\u003eThe pod is only half the setup. It runs the \u003cstrong\u003eLP1 coil series\u003c\/strong\u003e, which press straight into the base. The RPM 25W kit ships with an \u003cstrong\u003eLP1 Meshed 0.9ohm MTL\u003c\/strong\u003e coil, a solid all-rounder for salts. Keep spares from the \u003cstrong\u003e\u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" title=\"Vape Coils\" target=\"_blank\"\u003eVape Coils\u003c\/a\u003e\u003c\/strong\u003e range so a burnt coil never leaves you waiting.\u003c\/p\u003e\n\u003ch3\u003eAirflow You Can Actually Adjust\u003c\/h3\u003e\n\u003cp\u003eThe pod carries its own airflow ring that spins a full turn. Nudge it tighter for a cigarette-style MTL draw, or crack it open for a softer, airier pull. Small feature, fair enough, but it means one pod covers a couple of different moods without swapping hardware around.\u003c\/p\u003e\n\u003ch2\u003eSMOK RPM 25W Pod LP1 Coil Options\u003c\/h2\u003e\n\u003cp\u003eBecause the pod ships empty, the coil you pair with it decides how the whole thing vapes. They all come from SMOK's \u003cstrong\u003eLP1\u003c\/strong\u003e line, they all press-fit, and they all lean MTL. Here is the short version.\u003c\/p\u003e\n\u003cp\u003eMost popular is the \u003cstrong\u003eLP1 Meshed 0.9ohm MTL\u003c\/strong\u003e coil. It is the one bundled with the kit, sits happiest at around \u003cstrong\u003e17W\u003c\/strong\u003e, and handles nic salts cleanly with a warm, steady draw. Want something tighter and better suited to stronger salts? A \u003cstrong\u003e1.2ohm\u003c\/strong\u003e LP1 coil restricts the draw further and sips liquid more slowly. Prefer a bit more warmth and vapour instead? A lower-resistance LP1 mesh option around \u003cstrong\u003e0.8ohm\u003c\/strong\u003e pushes a little harder. Pick up LP1 \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/smok-vapes\" title=\"SMOK Coils\" target=\"_blank\"\u003e\u003cstrong\u003eSMOK Coils\u003c\/strong\u003e\u003c\/a\u003e separately and keep a couple spare.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLP1 Meshed 0.9ohm\u003c\/li\u003e\n\u003cli\u003eLP1 1.2ohm\u003c\/li\u003e\n\u003cli\u003eLP1 0.8ohm mesh\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Set Up the SMOK RPM 25W Pod\u003c\/h2\u003e\n\u003cp\u003eUnder two minutes, start to finish.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eLift the old pod straight off the device. It releases from the magnets with a gentle pull.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePress a fresh LP1 coil into the base of the pod until it clicks, then drip two or three drops of e-liquid onto the exposed cotton.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eEase back the silicone bung on the side and tilt your nic salt in slowly, stopping just below the fill line.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSeat the bung firmly back into the port until it sits flush.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStand the pod upright for a full six minutes so the cotton draws the liquid all the way through before you fire it.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClip the pod on and start around 12 to 15W, then work up to taste.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the SMOK RPM 25W Pod Box\u003c\/h2\u003e\n\u003cp\u003eThree empty RPM 25W pods, and that is it deliberately. No coils are fitted, so you will need \u003cstrong\u003eLP1 coils\u003c\/strong\u003e to go alongside them. There is no e-liquid and no device in the pack either. This is a straight replacement cartridge for people who already own the kit.\u003c\/p\u003e\n\u003ch2\u003eBuilt Only for the SMOK RPM 25W Pod Kit\u003c\/h2\u003e\n\u003cp\u003eThis cartridge fits one kit. The RPM 25W, and nothing else in the RPM family. It is easy to assume any RPM pod cross-fits, but they do not. It will not seat in the RPM 40. It will not run on the RPM 80 or RPM 80 Pro. The Nord pods are a different platform again.\u003c\/p\u003e\n\u003cp\u003e If your device says RPM 25W on it and takes LP1 coils, you are in the right place. Match it with other \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/refillable-pod-kits\" target=\"_blank\" title=\"Refillable Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eRefillable Pod Kits\u003c\/strong\u003e\u003c\/a\u003e only where they are explicitly LP1-based, and owners of other \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/mtl-vape-kits\" target=\"_blank\" title=\"MTL Vape Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eMTL Vape Kits\u003c\/strong\u003e\u003c\/a\u003e should check their own pod range instead.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK has been building pod and mod hardware since 2010, and the RPM line is one of its longest-running pod families. The RPM 25W sits at the compact, MTL-focused end of that range, paired with the LP1 coil platform rather than the older RPM coils.\u003c\/p\u003e\n\u003cp\u003eLP1 was designed around press-fit installation and leak resistance, with the coil sealing into a dedicated pod like this one. It is a mature, well-supported system, which is part of why replacement pods and coils for it stay easy to find, and Pirate Vapes keeps the pods and LP1 coils stocked side by side.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods are wear items. The plastic clouds, the seals soften, and eventually the flavour drops off no matter how carefully you look after them. Keeping a spare three-pack in the drawer means a tired cartridge never stops your day.\u003c\/p\u003e\n\u003cp\u003eEvery order from \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e ships same day when it is placed before 4 pm, packed to survive the post. Checkout is age-verified, over-18s only, and all stock is TPD compliant. Spend over £40 and delivery is free with Free Pirate Post.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe RPM 25W pod is a simple, sensible replacement part. If your kit's original cartridge has clouded or started leaking, a fresh three-pack and a new LP1 coil brings it back to how it vaped on day one; just remember the coils come separately.\u003c\/p\u003e\n\u003cp\u003eStock up on the LP1 you need, grab any spare \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e while you are at it, and browse the wider pod and coil range at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich device does the RPM 25W pod fit?\u003c\/h3\u003e\n\u003cp\u003eOnly the SMOK RPM 25W kit. Not the RPM 40, not the RPM 80, not the Nord series. Same brand, different pod platforms.\u003c\/p\u003e\n\u003ch3\u003eDoes the RPM 25W pod come with a coil?\u003c\/h3\u003e\n\u003cp\u003eNo. It is an empty cartridge. You add an LP1 coil separately.\u003c\/p\u003e\n\u003ch3\u003eWhat size is the RPM 25W pod?\u003c\/h3\u003e\n\u003cp\u003e2ml, the UK limit. You refill it by hand through the side port with whatever e-liquid you like.\u003c\/p\u003e\n\u003ch3\u003eCan I use nic salts in the RPM 25W pod?\u003c\/h3\u003e\n\u003cp\u003eYes, and honestly that is what it suits best. Pair a higher-resistance LP1 coil with a 10mg or 20mg nic salt for a smooth MTL hit. Freebase works too if you want a bigger cloud.\u003c\/p\u003e\n\u003ch3\u003eHow long does the RPM 25W pod last before it needs replacing?\u003c\/h3\u003e\n\u003cp\u003eDepends how hard you run it. Most people get a few weeks from one before the plastic clouds or the seal tears. Sweet, dark liquids shorten that. A three-pack keeps you covered for a good while.\u003c\/p\u003e\n\u003ch3\u003eHow many RPM 25W pods come in a pack?\u003c\/h3\u003e\n\u003cp\u003eThree. Enough to rotate through without reordering every week.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"Default Title","offer_id":52748810715418,"sku":null,"price":4.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/SMOK_RPM_25W_Replacement_Pods.jpg?v=1787849387"},{"product_id":"smok-fetch-pro-replacement-pods","title":"SMOK Fetch Pro Replacement Pods","description":"\u003ch2 class=\"font-heading-extra-bold margin0 h2\"\u003eSMOK Fetch Pro Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eTwo pod formats for one device, sold as a \u003cstrong\u003e3-pack\u003c\/strong\u003e of empty refillable pods for the SMOK \u003cstrong\u003eFetch Pro\u003c\/strong\u003e. The \u003cstrong\u003eRPM pod\u003c\/strong\u003e takes SMOK's RPM coil family for MTL and restricted draws. The \u003cstrong\u003eRGC pod\u003c\/strong\u003e runs the RGC coil range for sub-ohm \u003cstrong\u003eDTL\u003c\/strong\u003e. Both fill from the side through a silicone-stoppered port, both carry an adjustable airflow ring, and both clip to the mod on magnets.\u003c\/p\u003e\n\u003cp\u003eCoils are not included, so you choose the resistance to match how you vape. Genuine SMOK spares to keep a Fetch Pro alive. Browse the wider \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-pods\" target=\"_blank\" title=\"Vape Pods\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Pods\u003c\/strong\u003e\u003c\/a\u003e range too.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eTwo draw styles from one kit, because the RPM pod handles MTL while the RGC pod goes full sub-ohm DTL, so a single Fetch Pro can do both without you owning a second device.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSide fill with a silicone stopper. Top up without pulling the pod off the mod.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eAn airflow ring on the pod itself, which most replacement pods at this price quietly skip.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic click-in. No fiddly alignment.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eA 3-pack of genuine spares so a leak or a worn seal never puts the device out of action for long.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFetch Pro Pod Features\u003c\/h2\u003e\n\u003ch3\u003ePick Your Pod, Pick Your Draw\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eRPM pod\u003c\/strong\u003e is the MTL and restricted-lung side of the Fetch Pro, taking the full RPM coil family down to tighter, cigarette-style draws. The \u003cstrong\u003eRGC pod\u003c\/strong\u003e is the sub-ohm half, built around the \u003cstrong\u003e0.17ohm\u003c\/strong\u003e conical mesh for warm \u003cstrong\u003eDTL\u003c\/strong\u003e clouds. Same device, two personalities, depending on which pod is loaded. Grab spare \u003cstrong\u003e\u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Vape Coils\" rel=\"noopener\"\u003eVape Coils\u003c\/a\u003e\u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\"\u003e\u003c\/a\u003e\u003c\/strong\u003e to suit whichever you run.\u003c\/p\u003e\n\u003ch3\u003eSide Fill Beats the Old Way\u003c\/h3\u003e\n\u003cp\u003eRefilling is a side job here. Ease the silicone stopper out of the flank of the pod, drip your e-liquid in, push it back. The pod stays on the mod the whole time, so there is no unclipping, no drips down the battery door, no mess on your hands. Quick and clean enough to do at your desk.\u003c\/p\u003e\n\u003ch3\u003eWhy Adjustable Airflow Matters\u003c\/h3\u003e\n\u003cp\u003eMost replacement pods give you one fixed draw, and that is that. These do not. The airflow ring lets you widen it for a looser DTL pull or bring it in for a tighter MTL draw, so the same pod shifts with your mood or your coil. Small thing, real difference day to day.\u003c\/p\u003e\n\u003ch3\u003eBuilt for High VG on the RGC Side\u003c\/h3\u003e\n\u003cp\u003eThe RGC pod on a \u003cstrong\u003e0.17ohm\u003c\/strong\u003e mesh coil wants thick juice. High-VG is the move. A \u003cstrong\u003e70\/30\u003c\/strong\u003e shortfill wicks properly and holds its flavour from \u003cstrong\u003e40W\u003c\/strong\u003e upward, where a thin blend would dry out and taste scorched. Pair it with a \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/high-vg-e-liquid\" target=\"_blank\" title=\"High VG E-Liquid\" rel=\"noopener\"\u003e\u003cstrong\u003eHigh VG E-Liquid\u003c\/strong\u003e\u003c\/a\u003e and the RGC side does what it was built to do.\u003c\/p\u003e\n\u003ch3\u003eMagnets, Not Guesswork\u003c\/h3\u003e\n\u003cp\u003eThe pod drops onto the Fetch Pro and holds on magnets. No threading, no lining up a pin by feel. It seats the same way every time and pulls off cleanly when you swap. That magnetic contact keeps the connection steady while the airflow ring does its job at the base.\u003c\/p\u003e\n\u003ch2\u003eFetch Pro Pod Options\u003c\/h2\u003e\n\u003cp\u003eThree options in the picker. Choose by coil family first, then capacity.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRGC Pod (2ml)\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eRGC Pod (4ml)\u003c\/li\u003e\n\u003cli\u003eRPM Pod (4ml)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe \u003cstrong\u003e2ml pod\u003c\/strong\u003e is the TPD-capacity choice. The \u003cstrong\u003e4ml pods\u003c\/strong\u003e simply hold more between refills.\u003c\/p\u003e\n\u003ch2\u003eHow to Set Up the Fetch Pro Pod\u003c\/h2\u003e\n\u003cp\u003eCoil first, then fill. Five minutes, most of it soaking.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eTake your chosen RPM or RGC coil and press it firmly into the base of the pod until it seats. Plug and play, no threading.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePrime it with five or six drops of e-liquid straight onto the exposed coil cotton through the base.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOpen the silicone side stopper and fill the pod, keeping clear of the central airflow tube.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the stopper back in fully and wipe any excess off the base.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClip the pod onto the Fetch Pro and let it stand for a good seven minutes so the wick saturates before your first pull.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStart low, around 15W on an RPM coil or 40W on the RGC mesh, then build up toward the coil's rating.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the Fetch Pro Pod Box\u003c\/h2\u003e\n\u003cp\u003eEach pack has \u003cstrong\u003ethree empty Fetch Pro pods\u003c\/strong\u003e in your chosen type and capacity. That is all. No coils, no e-liquid, no device. You will need a compatible \u003cstrong\u003eRPM or RGC coil\u003c\/strong\u003e and your own juice to get going, and the pods only make sense if you already own the Fetch Pro. \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e stocks the coils separately.\u003c\/p\u003e\n\u003ch2\u003eMade for the SMOK Fetch Pro and Its Coil Families\u003c\/h2\u003e\n\u003cp\u003eThese pods are built for the \u003cstrong\u003eSMOK Fetch Pro\u003c\/strong\u003e, the box-style pod mod that sits between simple pods and full \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-mods\" target=\"_blank\" title=\"Vape Mods\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Mods\u003c\/strong\u003e\u003c\/a\u003e. The RPM pod accepts the RPM coil range: the \u003cstrong\u003e0.4ohm\u003c\/strong\u003e mesh for warmer MTL, the higher-ohm heads for tighter draws, and the \u003cstrong\u003eRPM RBA\u003c\/strong\u003e if you rebuild.\u003c\/p\u003e\n\u003cp\u003eThe RGC pod takes the RGC range, led by the \u003cstrong\u003e0.17ohm\u003c\/strong\u003e conical mesh for sub-ohm DTL, with an MTL and an RBA option alongside. What will not work: Nord coils do not fit either pod, and these pods do not drop into the smaller Fetch Mini. Match the coil to the pod, never across families.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK built the Fetch Pro around its \u003cstrong\u003eRPM and RGC coil platforms\u003c\/strong\u003e, the same plug-and-play system running across the Nord and RPM series. That cross-compatibility is the whole idea: one coil ecosystem covering everything from tight MTL to sub-ohm clouds, so a single brand of spares can feed a shelf of SMOK devices.\u003c\/p\u003e\n\u003cp\u003eThe Fetch Pro pods sit in that ecosystem as the refillable, coil-swappable option rather than a sealed cartridge. Browse the rest of the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/smok-vapes\" target=\"_blank\" title=\"SMOK Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eSMOK Coils\u003c\/strong\u003e\u003c\/a\u003e and hardware to match your setup.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods wear out well before devices do, so a spare \u003cstrong\u003e3-pack\u003c\/strong\u003e in the drawer saves a dead night when one starts to taste off or weeps at the seal. Since coils sell separately, it is worth grabbing a few of those at the same time.\u003c\/p\u003e\n\u003cp\u003eEvery order from \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e ships age-verified, \u003cstrong\u003eover-18s only\u003c\/strong\u003e, with all stock \u003cstrong\u003eTPD compliant\u003c\/strong\u003e. Free Pirate Post lands on orders over £40.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe Fetch Pro pods are the simple way to keep a two-style setup running: \u003cstrong\u003eRPM for MTL, RGC for clouds\u003c\/strong\u003e, both refillable and both coil-swappable. Buy the pod type that matches how you vape, add the right coil, and you are sorted.\u003c\/p\u003e\n\u003cp\u003eThey only suit the \u003cstrong\u003eFetch Pro\u003c\/strong\u003e, so double-check that it is your device before ordering. Pick up spare pods, coils, and \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e together at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eDo Fetch Pro Pod pods come with coils?\u003c\/h3\u003e\n\u003cp\u003eNo. They are empty pods, sold in threes. You will need an RPM or RGC coil to match, bought separately.\u003c\/p\u003e\n\u003ch3\u003eWhich Fetch Pro pod do I need, RPM or RGC?\u003c\/h3\u003e\n\u003cp\u003eRPM for MTL and tighter draws. RGC for sub-ohm DTL clouds. It comes down to the coil family you want to run.\u003c\/p\u003e\n\u003ch3\u003eDo Fetch Pro Pods fit the Fetch Mini?\u003c\/h3\u003e\n\u003cp\u003eNo. The Fetch Mini uses its own pods.\u003c\/p\u003e\n\u003ch3\u003eWhat e-liquid works best with Fetch Pro Pods?\u003c\/h3\u003e\n\u003cp\u003eRPM pods suit 50\/50 and nic salts for MTL. RGC pods want high-VG, around 70\/30, for sub-ohm DTL.\u003c\/p\u003e\n\u003ch3\u003eHow long does a Fetch Pro pod last?\u003c\/h3\u003e\n\u003cp\u003eWeeks, not days, since the pod outlives the coil. Swap it when it leaks, cracks, or the flavour muddies even with a fresh coil fitted.\u003c\/p\u003e\n\u003ch3\u003eCan one Fetch Pro pod take both coil types?\u003c\/h3\u003e\n\u003cp\u003eNo. RPM coils only fit the RPM pod, and RGC coils only fit the RGC pod. Keep them matched.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"RGC Pod (2ml)","offer_id":52755476119834,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RGC Pod (4ml)","offer_id":52755476152602,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RPM Pod (4ml)","offer_id":52755476185370,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/SMOK_Fetch_Pro_Replacement_Pods.jpg?v=1787986781"},{"product_id":"smok-rpm40-standard-pods","title":"Smok RPM40 Standard Pods","description":"\u003ch2\u003eSmok RPM40 Standard Pods\u003c\/h2\u003e\n\u003cp\u003eTwo pod formats, one device. The \u003cstrong\u003eSmok RPM40 Standard \u0026amp; Nord Pods\u003c\/strong\u003e are the refillable cartridges built for the Smok RPM40 kit, and the choice between them comes down to which coil family you run. The \u003cstrong\u003eRPM Standard Pod\u003c\/strong\u003e takes Smok's RPM coil range, while the \u003cstrong\u003eRPM Nord Pod\u003c\/strong\u003e takes Nord coils, and both use a \u003cstrong\u003eside-fill system\u003c\/strong\u003e with a silicone stopper to keep refills mess-free.\u003c\/p\u003e\n\u003cp\u003ePack of three. Bottom coil installation, no tools required. Whether you are running a tight MTL setup or pushing towards a warmer DTL draw, the coil you fit decides the style, and the pod just needs to be the right shape for it.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eTwo coil families in one device. Swap between the RPM Standard Pod and the RPM Nord Pod depending on whether you want RPM coils or Nord coils fitted, without buying a second kit.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eSide-fill design cuts the mess down. The silicone stopper seals properly, and refilling takes seconds once you have done it once or twice.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eBottom coil installation is simple. Push the coil in, click the pod into the device, done.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWorks across VG ratios. High VG and high PG liquids both run fine, so nic salts and freebase are both on the table.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eA pack of three means you are never stuck. Pods do wear out, and having spares on hand avoids a gap in your vaping while you wait on a reorder.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSmok RPM40 Pods Features\u003c\/h2\u003e\n\u003ch3\u003eBottom Coil, No Fuss\u003c\/h3\u003e\n\u003cp\u003eThe coil pushes into the base of the pod from underneath. No threading, no twisting, no guesswork about whether it has seated correctly. Push firmly until it clicks and you are set. This is the same fitting method Smok has used across most of the RPM range, so if you have owned an earlier Smok pod device, this will feel familiar straight away.\u003c\/p\u003e\n\u003ch3\u003eWhich Pod Actually Matters More Than It Looks\u003c\/h3\u003e\n\u003cp\u003eThe RPM Standard Pod and the RPM Nord Pod look similar side by side, but they are not interchangeable in terms of coil fit. Get the wrong one and your coil simply will not seat. \u003cstrong\u003eStandard Pod for RPM coils, Nord Pod for Nord coils.\u003c\/strong\u003e Worth double-checking which coil you already own before you order.\u003c\/p\u003e\n\u003ch3\u003eSide Fill That Actually Seals\u003c\/h3\u003e\n\u003cp\u003eOlder pod systems used a plug that worked loose over time and started to weep liquid from the seam. The \u003cstrong\u003esilicone stopper\u003c\/strong\u003e on these pods sits tighter, and the fill port is positioned away from the airflow channel, so liquid stays where it should. Not a leak-proof guarantee (nothing is), but a noticeably tighter seal than the pods this replaced.\u003c\/p\u003e\n\u003ch3\u003eOne Device, Two Vaping Styles\u003c\/h3\u003e\n\u003cp\u003eFit an RPM coil (such as the \u003cstrong\u003e0.4ohm mesh\u003c\/strong\u003e) to lean into a warmer, airier DTL vape with dense clouds. Fit a Nord coil if you prefer a tighter, more classic MTL draw with higher resistance. You can pick from the wider \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\"\u003e\u003cstrong\u003eVape Coils\u003c\/strong\u003e\u003c\/a\u003e range. The pod acts as the vessel, while your coil selection tailors the exact draw.\u003c\/p\u003e\n\u003ch3\u003eBuilt for Daily Use, Not Just Occasional Top-Ups\u003c\/h3\u003e\n\u003cp\u003ePod shells crack, stoppers perish, and coil housings wear out with repeated use. A \u003cstrong\u003ethree-pack\u003c\/strong\u003e means you are covered for the next few months of regular refilling rather than reordering every few weeks. Keep one as backup in a drawer, and you will not be caught out mid-week.\u003c\/p\u003e\n\u003ch2\u003eSmok RPM40 Pods Options\u003c\/h2\u003e\n\u003cp\u003eSelect the pod that matches your coil family and preferred capacity:\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM Nord Pod 2ml\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eRPM Nord Pod 4.5ml\u003c\/li\u003e\n\u003cli\u003eRPM Standard Pod 4.3ml\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eIf you are stocking up on more than one pack, browse the wider refills and pods range for other compatible options.\u003c\/p\u003e\n\u003ch2\u003eHow to Set Up the Smok RPM40 Pods\u003c\/h2\u003e\n\u003cp\u003eQuick swap. A couple of minutes from empty pod to first vape.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003ePull the empty pod straight out of the RPM40 device.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the coil out from the bottom of the old pod and set it aside.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFit your chosen coil into the base of the replacement pod, whether that is an RPM coil for the Standard Pod or a Nord coil for the Nord Pod. Push until it clicks into place.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOpen the silicone stopper on the side of the pod and fill with your e-liquid, leaving a small air gap at the top. Do not overfill.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLet the coil settle for seven to eight minutes before your first draw, giving the wick time to fully saturate.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClick the pod back into the device and start on a low setting before building up.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the Smok RPM40 Standard \u0026amp; Nord Pods Box\u003c\/h2\u003e\n\u003cp\u003eThree pods per pack, either all Standard or all Nord depending on which you order. No coils included, no device, no e-liquid. This is a \u003cstrong\u003epod-only pack\u003c\/strong\u003e, so make sure you already have compatible coils on hand before it arrives.\u003c\/p\u003e\n\u003ch2\u003eMade for the Smok RPM40, Nothing Else\u003c\/h2\u003e\n\u003cp\u003eThese pods are built specifically for the \u003cstrong\u003eSmok RPM40 kit\u003c\/strong\u003e and are not designed to fit other Smok devices, even ones that look similar from the outside. If your device is an RPM40, either pod option will click straight in.\u003c\/p\u003e\n\u003cp\u003eWhat they do not fit: the RPM4, RPM100, RPM2, or any of Smok's Nord-branded standalone kits. Each of those runs its own pod shape, even where the coil compatibility overlaps on paper. Check your device model before ordering to avoid a pod that will not seat.\u003c\/p\u003e\n\u003ch2\u003eAbout Smok\u003c\/h2\u003e\n\u003cp\u003eSmok built the RPM series around one idea: let vapers switch coil types without switching devices. The RPM40 was one of the first kits to properly commit to that, offering both RPM and Nord pod compatibility from a single mod rather than locking owners into one coil family.\u003c\/p\u003e\n\u003cp\u003eThat flexibility is why the platform has stuck around, and why replacement pods for it are still in steady demand years after launch. For UK vapers who already own coils from either range, it means the device adapts rather than the other way round.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003ePods do not last forever, and running out mid-week with a full bottle of e-liquid and nothing to put it in is a familiar frustration. A spare pack sitting in a drawer solves that before it happens.\u003c\/p\u003e\n\u003cp\u003eEvery order from \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e ships same-day before 4 pm in padded packaging, so pods arrive intact rather than rattling around loose. All stock across our \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/tpd-compliant-vapes\"\u003e\u003cstrong\u003eTPD-Compliant Vapes\u003c\/strong\u003e\u003c\/a\u003e range meets current UK regulation, with an age-verified checkout and sales restricted to over 18s only.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSmok RPM40 Standard \u0026amp; Nord Pods\u003c\/strong\u003e keep an already flexible device running exactly the way you want it. Pick the Standard Pod for RPM coils or the Nord Pod for Nord coils, fit your coil of choice, and you have got both MTL and DTL options from the same kit.\u003c\/p\u003e\n\u003cp\u003eA \u003cstrong\u003ethree-pack\u003c\/strong\u003e covers you for months, and the side-fill design means less mess than older-style pods. If your RPM40 is due a refresh, browse the full range of \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e alongside these pods at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich pod fits my coils?\u003c\/h3\u003e\n\u003cp\u003eRPM coils go in the RPM Standard Pod. Nord coils go in the RPM Nord Pod. Check the coil packaging if you are not sure which range you own.\u003c\/p\u003e\n\u003ch3\u003eDo these fit any other Smok device?\u003c\/h3\u003e\n\u003cp\u003eNo. Built for the RPM40 only.\u003c\/p\u003e\n\u003ch3\u003eCan I use nic salts in these pods?\u003c\/h3\u003e\n\u003cp\u003eYes, alongside freebase and shortfill liquids. Both high VG and high PG blends work, so the choice comes down to the coil fitted rather than the pod itself.\u003c\/p\u003e\n\u003ch3\u003eHow much can I fill the pod with?\u003c\/h3\u003e\n\u003cp\u003eIt depends on the size you choose. The RPM Standard holds up to 4.3ml, the larger RPM Nord holds up to 4.5ml, and the 2ml Nord edition holds 2ml. Always leave a tiny air gap at the top to prevent pressure leaks.\u003c\/p\u003e\n\u003ch3\u003eDo the pods come with coils included?\u003c\/h3\u003e\n\u003cp\u003eNo. Pods only. Coils are sold separately in the RPM and Nord ranges.\u003c\/p\u003e\n\u003ch3\u003eHow often do these pods need replacing?\u003c\/h3\u003e\n\u003cp\u003eMost vapers get a few weeks of regular use before the stopper or seal starts to wear. Having a spare pack on hand avoids a gap between old and new.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"RPM Nord Pod 2ml","offer_id":52771084402970,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RPM Nord Pod 4.5ml","offer_id":52771084435738,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RPM Standard Pod 4.3ml","offer_id":52771084468506,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/Smok_RPM40_Standard_Pods.jpg?v=1788171575"},{"product_id":"smok-rpm80-rgc-2ml-5ml-pods","title":"Smok RPM80 RGC 2ml\/5ml Replacement Pods","description":"\u003ch2\u003eSmok RPM80 RGC 2ml\/5ml Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eAdjustable airflow changes what a pod can do, and that is the whole point of the \u003cstrong\u003eRGC pod\u003c\/strong\u003e. The \u003cstrong\u003eSmok RPM80 RGC 2ml\/5ml Replacement Pods\u003c\/strong\u003e are built for the \u003cstrong\u003eSmok RPM80 Kit\u003c\/strong\u003e and the RPM80 Pro, taking the \u003cstrong\u003eRGC conical mesh coil\u003c\/strong\u003e rather than the standard RPM range.\u003c\/p\u003e\n\u003cp\u003eA \u003cstrong\u003edual airflow ring\u003c\/strong\u003e sits under the coil, so you can open the draw up for warmer DTL clouds or close it down for something tighter. \u003cstrong\u003eMagnetic pod connection, rubber plug refill, no tools needed.\u003c\/strong\u003e Choose 2ml if you want the UK-compliant fill line, or 5ml if you are stocking the international-capacity shell. \u003cstrong\u003ePack of three, coils sold separately.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eAdjustable airflow that actually changes the draw. The dual-slot ring under the coil lets you tighten or open the pull, rather than being stuck with one fixed setting.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eBuilt specifically for the RGC coil. This is not a general-purpose RPM pod; it is shaped for the conical mesh design that made the RPM80 series stand out.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eMagnetic connection holds firm. Click it in, and it stays. No wobble, no accidental disconnects mid-vape.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eRefill without removing the pod. The rubber plug sits on top, so you can top up on the go.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTwo capacities to choose from. Pick 2ml for the straightforward UK-line fill, or 5ml if the shell size and clarity matter more to you.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStocked and dispatched fast. Pirate Vapes keeps both pod sizes in regular stock, so a worn seal does not mean a long wait.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSmok RPM80 RGC Pods Features\u003c\/h2\u003e\n\u003ch3\u003eConical Mesh Changes the Airflow Path\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eRGC coil\u003c\/strong\u003e is not shaped like a standard mesh coil. Its conical structure narrows the airflow as it approaches the coil surface, then opens out again towards the mouthpiece. That funnel effect is what gives the \u003cstrong\u003eRGC platform\u003c\/strong\u003e its reputation for dense vapour and stronger flavour transfer compared with the flat mesh used in most RPM40 coils. Worth trying if you have only ever run standard RPM coils in the older kit.\u003c\/p\u003e\n\u003ch3\u003eThe Airflow Ring Actually Does Something\u003c\/h3\u003e\n\u003cp\u003ePlenty of pods claim adjustable airflow and deliver barely a noticeable difference. The \u003cstrong\u003eRGC pod's dual-slot ring\u003c\/strong\u003e sits directly under the coil, close to where the vapour is being produced, so closing it down genuinely tightens the draw and opens it up for a proper DTL pull. Fair enough if you switch between the two depending on mood or e-liquid strength. That flexibility is rare at this end of the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Coil Range\" rel=\"noopener\"\u003e\u003cstrong\u003eCoil Range\u003c\/strong\u003e\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eRefill Without the Faff\u003c\/h3\u003e\n\u003cp\u003eOlder pod systems made you pull the whole cartridge to top it up. The \u003cstrong\u003erubber plug on the RGC pod\u003c\/strong\u003e sits accessible from the top, so a quick refill takes seconds without breaking the magnetic seal. Handy mid-session when you do not want to keep dismantling the device.\u003c\/p\u003e\n\u003ch3\u003eMagnetic, Not Friction-Fit\u003c\/h3\u003e\n\u003cp\u003eThe pod clicks into the \u003cstrong\u003eRPM80 body\u003c\/strong\u003e with a genuine magnetic hold rather than a loose friction fit that can work its way out in a pocket. Two pins inside the device make contact with the coil once seated, with very little wobble even after regular use.\u003c\/p\u003e\n\u003ch3\u003eTwo Capacities, Same Coil Platform\u003c\/h3\u003e\n\u003cp\u003eWhether you go \u003cstrong\u003e2ml or 5ml\u003c\/strong\u003e, the coil compatibility and airflow mechanism are identical. The difference is shell size and how much liquid you can see through the transparent body at a glance. Neither changes performance, so pick based on whichever fits your refill habits.\u003c\/p\u003e\n\u003ch2\u003eSmok RPM80 RGC Pods Options\u003c\/h2\u003e\n\u003cp\u003eBoth options run the same \u003cstrong\u003eRGC coil platform\u003c\/strong\u003e. The choice is really about fill visibility and how often you like to top up.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eRPM80 RGC Pod (2ml)\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eRPM80 RGC Pod (5ml)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBrowse the wider refills and pods range if you are stocking up on more than the RGC line.\u003c\/p\u003e\n\u003ch2\u003eHow to Set Up the Smok RPM80 RGC Pods\u003c\/h2\u003e\n\u003cp\u003eA few minutes from empty pod to first draw.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003ePull the empty pod free from the top of the RPM80 or RPM80 Pro. The magnets release with a firm, even pull.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the old coil out from the base and set it aside.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFit your RGC coil into the bottom of the new pod, pressing until it clicks fully into place.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLift the rubber plug on top of the pod and fill with your chosen high VG e-liquid up to the 2ml line.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLet it sit for ten minutes, then take a couple of gentle dry pulls before firing to help draw liquid fully into the mesh.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eClick the pod back into the device, adjust the airflow ring to taste, and start at a moderate wattage before building up.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the Smok RPM80 RGC Pods Box\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eThree RGC replacement pods\u003c\/strong\u003e, either all 2ml or all 5ml depending on which size you order. No coils included, no device, no e-liquid. Coils for the RGC platform need to be bought separately.\u003c\/p\u003e\n\u003ch2\u003eBuilt for the RPM80 and RPM80 Pro RGC Platform\u003c\/h2\u003e\n\u003cp\u003eThese pods are shaped specifically around the \u003cstrong\u003eRGC coil system\u003c\/strong\u003e used in the Smok RPM80 and RPM80 Pro, and they are not interchangeable with the standard RPM pod that ships alongside them in the same kit. If you are running \u003cstrong\u003eRPM coils rather than RGC\u003c\/strong\u003e, this is not the pod you need.\u003c\/p\u003e\n\u003cp\u003eWhat they do not fit: the \u003cstrong\u003eoriginal RPM40, the RPM100, or any of Smok's Nord-branded kits.\u003c\/strong\u003e Even devices with similar naming run their own pod shape, so double-check which coil platform your \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-mods\" target=\"_blank\" title=\"Vape Mods\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Mods\u003c\/strong\u003e\u003c\/a\u003e or kit is built around before ordering.\u003c\/p\u003e\n\u003ch2\u003eAbout Smok\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eRGC coil\u003c\/strong\u003e was Smok's answer to the flat-mesh limitations of the original RPM range. Its conical shape, developed under the nexMesh label, concentrates airflow through the coil rather than letting it spread evenly, which is what gives RGC-based devices their denser vapour output.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eRPM80 and RPM80 Pro\u003c\/strong\u003e were the first kits built around this coil, and the adjustable airflow ring on the RGC pod was a deliberate move to let vapers tune that density rather than accept one fixed draw.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003eRunning the \u003cstrong\u003eRGC platform daily\u003c\/strong\u003e means the coil and pod seal both see regular wear, and a spare pod on hand means a worn seal does not turn into a wasted refill.\u003c\/p\u003e\n\u003cp\u003eAt \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e, every order ships same-day before 4 pm, and the full \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/tpd-compliant-vapes\" target=\"_blank\" title=\"TPD-Compliant Vapes\" rel=\"noopener\"\u003e\u003cstrong\u003eTPD-Compliant Vapes\u003c\/strong\u003e\u003c\/a\u003e range meets current UK regulations, with an age-verified checkout and sales restricted to over 18s only.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSmok RPM80 RGC 2ml\/5ml Replacement Pods\u003c\/strong\u003e keep the airflow-adjustable side of your RPM80 or RPM80 Pro running properly. Pick the \u003cstrong\u003e2ml pod\u003c\/strong\u003e for a straightforward UK fill or the \u003cstrong\u003e5ml shell\u003c\/strong\u003e for easier level tracking, fit your RGC coil, and the dual-slot airflow ring gives you a genuinely adjustable draw rather than a token gesture at customisation.\u003c\/p\u003e\n\u003cp\u003eA \u003cstrong\u003ethree-pack\u003c\/strong\u003e should keep you covered for a good stretch of regular use. Browse the full range of \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e alongside these pods at \u003ca href=\"https:\/\/piratevapes.co.uk\/\" target=\"_blank\" title=\"Pirate Vapes\" rel=\"noopener\"\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eDoes this pod fit the standard RPM40?\u003c\/h3\u003e\n\u003cp\u003eNo. Built for the RPM80 and RPM80 Pro RGC platform only.\u003c\/p\u003e\n\u003ch3\u003eWhat coils go in the RGC pod?\u003c\/h3\u003e\n\u003cp\u003eThe RGC Conical Mesh coil, 0.17ohm as standard, with an RBA option sold separately for rebuildable builds.\u003c\/p\u003e\n\u003ch3\u003eCan I use nic salts in the RGC pod?\u003c\/h3\u003e\n\u003cp\u003eNot recommended at this resistance. The 0.17ohm coil is built for high VG shortfill rather than nic salts, and running high-strength salts through a sub-ohm coil gives a harsh result.\u003c\/p\u003e\n\u003ch3\u003eWhat is the difference between the 2ml and 5ml pod?\u003c\/h3\u003e\n\u003cp\u003eSame coil platform and airflow system. The 5ml shell is simply larger, giving a clearer view of remaining liquid, though the UK fill line still sits at 2ml on both.\u003c\/p\u003e\n\u003ch3\u003eDoes the airflow ring make a real difference?\u003c\/h3\u003e\n\u003cp\u003eYes. Closing it down tightens the draw noticeably, and opening it fully gives a much airier, DTL-style pull. It is a genuine adjustment, not a cosmetic one.\u003c\/p\u003e\n\u003ch3\u003eHow long does an RGC coil last?\u003c\/h3\u003e\n\u003cp\u003eTypically one to two weeks with regular use, sooner with sweeter or higher-VG liquids that leave residue on the mesh faster.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"RPM80 RGC Pod (2ml)","offer_id":52771088826650,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true},{"title":"RPM80 RGC Pod (5ml)","offer_id":52771088859418,"sku":null,"price":5.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/Smok_RPM80_RGC_2ml_5ml_Replacement_Pods.jpg?v=1788172431"},{"product_id":"smok-ipx80-replacement-pods","title":"Smok IPX80 Replacement Pods","description":"\u003ch2\u003eSmok IPX80 Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eA \u003cstrong\u003e2ml refillable pod\u003c\/strong\u003e built specifically for the \u003cstrong\u003eSMOK IPX80\u003c\/strong\u003e pod kit, taking the \u003cstrong\u003eRPM 2 coil range\u003c\/strong\u003e. Side-fill through a silicone-stoppered port, so there is no popping the whole pod apart just to top up. \u003cstrong\u003ePress-fit coil installation\u003c\/strong\u003e means the coil clicks straight into the base without threading.\u003c\/p\u003e\n\u003cp\u003eRuns on either the \u003cstrong\u003e0.6ohm DC MTL coil\u003c\/strong\u003e for a tighter, cigarette-style draw or the \u003cstrong\u003e0.16ohm mesh coil\u003c\/strong\u003e for warmer, cloudier pulls, both sold separately. If your original IPX80 pod has cracked, clouded over, or just won't seal properly any more, this is the direct replacement.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eSide-fill design means topping up takes seconds, no fiddly top-cap to wrestle with, and the silicone stopper seals tight enough to survive a jacket pocket\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eGenuine RPM 2 fitment, so it clicks into the SMOK IPX80 the way it's meant to, first time\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWorks with two coil resistances from the same pod, which covers both MTL and warmer DTL-leaning styles\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePress-fit coil installation takes the guesswork out of swaps. No threading, no cross-fitting a coil at an angle\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eA spare pod in the drawer means one crack or leak doesn't take your whole IPX80 out of action\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSmok IPX80 Replacement Pods Features\u003c\/h2\u003e\n\u003ch3\u003eBuilt with a Practical Side-Fill\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003efill port sits on the side of the pod\u003c\/strong\u003e, sealed with a silicone stopper. Pull it back, fill, and push it home. No top cap to lose, and no juice running down the device because you rushed a refill on the way out the door. It is a small design choice that makes daily use much cleaner.\u003c\/p\u003e\n\u003ch3\u003eTwo Coils, One Pod. Genuinely Useful?\u003c\/h3\u003e\n\u003cp\u003eFair enough if that sounds like a small thing. It is not. The same pod body accepts both the \u003cstrong\u003e0.6ohm DC MTL coil\u003c\/strong\u003e and the \u003cstrong\u003e0.16ohm mesh coil\u003c\/strong\u003e, so switching your draw style doesn't mean buying a new pod every time. Restricted MTL one week, warmer mesh the next. One pod handles both.\u003c\/p\u003e\n\u003ch3\u003ePress-Fit, Not Threaded\u003c\/h3\u003e\n\u003cp\u003eRPM 2 coils drop into the base and lock with a firm push. That is it. No cross-threading a coil at 11 pm with the lights off, no stripped threads after six months of daily swaps. \u003cstrong\u003ePress-fit coil installation\u003c\/strong\u003e is simply less that can go wrong.\u003c\/p\u003e\n\u003ch3\u003eThe Silicone Stopper Actually Seals\u003c\/h3\u003e\n\u003cp\u003eCheaper refillable pods leak from the fill port within a few refills. SMOK's \u003cstrong\u003esilicone stopper\u003c\/strong\u003e on this pod holds its seal noticeably longer, which matters more than it sounds like it should when the pod is riding around in a bag next to your phone.\u003c\/p\u003e\n\u003ch3\u003eA Direct Fit, Not a Universal One\u003c\/h3\u003e\n\u003cp\u003eThis pod is built for the \u003cstrong\u003eSMOK IPX80\u003c\/strong\u003e specifically. It does not fit the standard RPM pod kits, the RPM40, or any of SMOK's Nord-series devices. If you're not certain which device you're running, check the model printed on the base of your kit before ordering.\u003c\/p\u003e\n\u003ch2\u003eSmok IPX80 Replacement Pods Compatible Coil Options\u003c\/h2\u003e\n\u003cp\u003eTwo coils fit this pod, and the right one depends entirely on how you like to draw.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e0.6ohm DC MTL:\u003c\/strong\u003e Tighter draw, 12–25W, best with nic salts\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cstrong\u003e0.16ohm Mesh:\u003c\/strong\u003e Warmer draw, 25–50W, better with 50\/50 or high-VG liquid\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Set Up the Smok IPX80 Replacement Pods\u003c\/h2\u003e\n\u003cp\u003eStraightforward swap. A couple of minutes, most of it spent waiting.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eRemove the empty or damaged pod from the IPX80 by pulling it straight up out of the device.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTake your chosen RPM 2 coil and press it firmly into the base of the new pod until it clicks into place.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePeel back the silicone stopper on the side of the pod and fill with your e-liquid, keeping clear of the central airflow tube.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the stopper back down to seal the fill port properly.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLet the coil rest for six minutes before your first draw, giving the cotton time to fully soak through.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eInsert the pod into the device and start at the low end of the coil's rated wattage, increasing gradually from there.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the Smok IPX80 Replacement Pods Box\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eempty replacement pod\u003c\/strong\u003e, or pods depending on the pack size selected at checkout. \u003cstrong\u003eNo coil included\u003c\/strong\u003e, no e-liquid, and no device. This is a pod-only replacement, so make sure you have \u003cstrong\u003eRPM 2 coils\u003c\/strong\u003e and your preferred e-liquid ready before it arrives.\u003c\/p\u003e\n\u003ch2\u003eBuilt Specifically for the SMOK IPX80 Pod Kit\u003c\/h2\u003e\n\u003cp\u003eThis pod is a \u003cstrong\u003edirect fit for the SMOK IPX80\u003c\/strong\u003e, and nothing else. It slots into the IPX80's pod bay and locks in exactly the way the original included pod did, taking the full \u003cstrong\u003eRPM 2 Coils\u003c\/strong\u003e range.\u003c\/p\u003e\n\u003cp\u003eWhat it does not fit: the \u003cstrong\u003eoriginal RPM pod kit, the RPM40, RPM100, or any SMOK Nord device.\u003c\/strong\u003e Each of those runs a different pod shape and a different coil platform entirely. If your device isn't an IPX80, this pod will not seat correctly, so it's worth double-checking the model before you add it to your basket.\u003c\/p\u003e\n\u003ch2\u003eAbout SMOK\u003c\/h2\u003e\n\u003cp\u003eSMOK has spent over a decade building some of the most widely used \u003cstrong\u003epod and coil platforms\u003c\/strong\u003e in vaping, and the RPM series is one of the reasons why. Rather than locking every device into its own proprietary pod, SMOK built the \u003cstrong\u003eRPM and RPM 2 ranges\u003c\/strong\u003e to work across multiple kits, which is exactly why the IPX80 uses the same coil family as several other SMOK devices.\u003c\/p\u003e\n\u003cp\u003eThat cross-compatibility keeps ongoing running costs down and means coils are rarely hard to find. The IPX80 itself leans into SMOK's more rugged, outdoor-oriented design language, and this pod is built to match: \u003cstrong\u003esealed, refillable, and straightforward to maintain.\u003c\/strong\u003e\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003eOne pod is fine until it isn't, and a cracked or leaking pod with no spare on hand means your IPX80 is out of action until the next order lands. Picking up a spare pod alongside a couple of \u003cstrong\u003eRPM 2 coils\u003c\/strong\u003e covers you for months, not days.\u003c\/p\u003e\n\u003cp\u003eEvery order from \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e ships the same day before 4 pm in padded packaging, with an age-verified checkout and full \u003cstrong\u003eTPD compliance\u003c\/strong\u003e on every listing. \u003cstrong\u003eOver 18s only\u003c\/strong\u003e. Free Pirate Post on orders over £40.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eSmok IPX80 Replacement Pods\u003c\/strong\u003e are a simple, direct fix for a device that otherwise stops working the moment its pod fails. \u003cstrong\u003eSide-fill convenience, press-fit coils, \u003c\/strong\u003eand compatibility with both the\u003cstrong\u003e 0.6ohm MTL and 0.16ohm mesh options\u003c\/strong\u003e mean one pod covers two very different vaping styles.\u003c\/p\u003e\n\u003cp\u003eIf your IPX80's original pod has seen better days, this is the exact replacement it needs. Browse the full range of \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/smok-vapes\" target=\"_blank\" title=\"SMOK Vapes\" rel=\"noopener\"\u003e\u003cstrong\u003eSMOK Vapes\u003c\/strong\u003e\u003c\/a\u003e and \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Vape Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Coils\u003c\/strong\u003e\u003c\/a\u003e to build a proper spares kit, or head back to \u003ca href=\"https:\/\/piratevapes.co.uk\/\" target=\"_blank\" title=\"Pirate Vapes\" rel=\"noopener\"\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e\u003c\/a\u003e to see what else is in stock.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eDoes the pod come with a coil?\u003c\/h3\u003e\n\u003cp\u003eNo. This is a pod-only replacement. You'll need to pick up 0.6ohm DC MTL or 0.16ohm mesh RPM 2 coils separately.\u003c\/p\u003e\n\u003ch3\u003eWill this pod fit my SMOK RPM40?\u003c\/h3\u003e\n\u003cp\u003eNo, these pods do not fit the SMOK RPM40.\u003c\/p\u003e\n\u003ch3\u003eHow much e-liquid does the pod hold?\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e2ml\u003c\/strong\u003e, in line with UK regulations. It's a refillable pod, so you can top it up as many times as you like once it's empty.\u003c\/p\u003e\n\u003ch3\u003eWhich coil should I pick for nic salts?\u003c\/h3\u003e\n\u003cp\u003eThe 0.6ohm DC MTL coil. It's built for a tighter draw and pairs well with higher-strength nic salts.\u003c\/p\u003e\n\u003ch3\u003eHow long does the silicone stopper last before it needs replacing?\u003c\/h3\u003e\n\u003cp\u003eMost vapers get many months of daily refills before the seal starts to loosen. If it stops sealing properly, replace the pod rather than the whole device.\u003c\/p\u003e\n\u003ch3\u003eCan I use this pod with mesh and MTL coils at the same time?\u003c\/h3\u003e\n\u003cp\u003eNot simultaneously, but you can swap between the two coil types in the same pod whenever you like, so long as you give the new coil time to soak before vaping.\u003c\/p\u003e","brand":"SMOK","offers":[{"title":"RPM Pod","offer_id":52771129786650,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"RPM 2 Pod","offer_id":52771129819418,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/Smok_IPX80_Replacement_Pods.jpg?v=1788174596"}],"url":"https:\/\/piratevapes.co.uk\/collections\/smok-pods.oembed","provider":"Pirate Vapes","version":"1.0","type":"link"}