{"product_id":"aspire-bvc-replacement-coils","title":"Aspire BVC Replacement Coils","description":"\u003ch2\u003eAspire BVC Replacement Coils\u003c\/h2\u003e\n\u003cp\u003eFlavour gone flat on an old Aspire pen tank? Nine times out of ten it is not the kit that is finished, just the coil. The \u003cstrong\u003eAspire BVC Replacement Coils\u003c\/strong\u003e are a pack of five \u003cstrong\u003ebottom vertical coil\u003c\/strong\u003e heads built for Aspire's classic clearomisers: the \u003cstrong\u003eK1\u003c\/strong\u003e, \u003cstrong\u003eK2\u003c\/strong\u003e, \u003cstrong\u003eCE5\u003c\/strong\u003e, \u003cstrong\u003eCE5-S\u003c\/strong\u003e, \u003cstrong\u003eET\u003c\/strong\u003e and \u003cstrong\u003eET-S\u003c\/strong\u003e. All sit above 1ohm, all run at low \u003cstrong\u003ewattage\u003c\/strong\u003e, all wicked with \u003cstrong\u003eorganic cotton\u003c\/strong\u003e for a clean \u003cstrong\u003eMTL\u003c\/strong\u003e draw.\u003c\/p\u003e\n\u003cp\u003ePick a resistance, screw it in, top up with \u003cstrong\u003e50\/50\u003c\/strong\u003e juice or \u003cstrong\u003eNic Salts\u003c\/strong\u003e, and you are back to full flavour. Five heads, one simple job.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eGenuine Aspire heads, not clones. Each coil carries Aspire's scratch-and-check security panel, so the flavour and lifespan you had from the coil in your original tank is what you get from a replacement, pack after pack.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFive in a box. Enough to keep an old clearomiser running for well over a month at typical daily use.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eThree resistances to fine-tune warmth and throat hit without touching a single device setting.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOrganic cotton wicks cleaner than the old silica, so flavour reads true from the first fill.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eLow wattage barely dents battery life, which counts for a lot on the slim pen batteries these tanks usually sit on.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eAspire BVC Coil Features\u003c\/h2\u003e\n\u003ch3\u003eWhy Does Coil Position Matter?\u003c\/h3\u003e\n\u003cp\u003eBVC stands for \u003cstrong\u003ebottom vertical coil\u003c\/strong\u003e. The heating element stands upright inside the housing instead of lying flat, which lets the \u003cstrong\u003eorganic cotton\u003c\/strong\u003e feed liquid from both sides at once. Older \u003cstrong\u003eBDC\u003c\/strong\u003e clearomiser heads burned unevenly and gunked up fast. Standing the coil vertical was Aspire's fix, and it still holds up.\u003c\/p\u003e\n\u003ch3\u003eOrganic Cotton, Cleaner Taste\u003c\/h3\u003e\n\u003cp\u003eEarly Aspire clearomiser coils leaned on silica wicking. Remember that faint plasticky note on the first few draws of a fresh head? That was the silica. These use \u003cstrong\u003eorganic cotton\u003c\/strong\u003e instead, so the break-in is shorter and the flavour comes through honestly from the first fill. Small swap, real difference.\u003c\/p\u003e\n\u003ch3\u003eThese Want Thin Juice\u003c\/h3\u003e\n\u003cp\u003eThe wicking ports are cut for \u003cstrong\u003e50\/50\u003c\/strong\u003e or higher-PG liquid, and that is deliberate. Classic clearomisers have narrow feed channels and low output, so thick max-VG juice will not wick fast enough and you get dry hits within minutes. Pair them the way MTL clearomisers and \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/mtl-tanks\" target=\"_blank\" title=\"MTL Tanks\" rel=\"noopener\"\u003e\u003cstrong\u003eMTL Tanks\u003c\/strong\u003e\u003c\/a\u003e were always meant to run.\u003c\/p\u003e\n\u003ch3\u003eBarely Sips Your Battery!\u003c\/h3\u003e\n\u003cp\u003eDepending on resistance, these draw somewhere around \u003cstrong\u003e7 to 14W\u003c\/strong\u003e. That is single-digit territory for a good chunk of the range, so a slim pen battery lasts. Carry an Aspire pen to work and vape through the day, and you are not hunting for a charger by lunch. Engineering built for small batteries, still doing the job.\u003c\/p\u003e\n\u003ch3\u003eScratch the Panel, Know It Is Real\u003c\/h3\u003e\n\u003cp\u003eEvery genuine pack ships with a \u003cstrong\u003escratch-and-check\u003c\/strong\u003e security panel on the box. Reveal the code, verify it, and you know these are the real thing rather than a factory copy. Third-party BVC-style heads are everywhere and build quality is a lottery. Real Aspire coils give you the same spec every single time.\u003c\/p\u003e\n\u003ch2\u003eBVC Coil Resistance Options\u003c\/h2\u003e\n\u003cp\u003eThree heads share the picker, all MTL, all low power. What changes is how warm and how firm the draw feels.\u003c\/p\u003e\n\u003cp\u003eStart with the \u003cstrong\u003e1.6ohm\u003c\/strong\u003e if you are unsure. It runs warm without tipping into hot, gives a satisfying throat hit, and pairs well with mid-strength freebase for a draw close to a cigarette. Most people settle here.\u003c\/p\u003e\n\u003cp\u003ePrefer something softer? The \u003cstrong\u003e1.8ohm\u003c\/strong\u003e cools things down a touch. Less warmth, a gentler hit, and it takes higher-strength salts comfortably. A sensible choice for lighter sessions.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003e1.2ohm\u003c\/strong\u003e sits at the warm end of this little range. A bit more vapour, a bit more heat, best near the top of the wattage window if your battery reaches it. Not for everyone, but the warmest option on offer.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1.2ohm\u003c\/li\u003e\n\u003cli\u003e1.6ohm\u003c\/li\u003e\n\u003cli\u003e1.8ohm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Set Up the BVC Coils\u003c\/h2\u003e\n\u003cp\u003eTwo minutes, no mess.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eUnscrew the tank base from the battery and remove the spent coil. It threads out anticlockwise.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eDrip three drops of e-liquid straight onto the exposed cotton at the coil ports, then one more down the centre.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eScrew the fresh head into the base clockwise until it is finger-tight. Do not force it.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eReassemble and fill with 50\/50 e-liquid (grab a bottle from the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/50-50-e-liquids\" target=\"_blank\" title=\"50\/50 E-Liquid\" rel=\"noopener\"\u003e\u003cstrong\u003e50\/50 E-Liquid\u003c\/strong\u003e\u003c\/a\u003e range if you are out).\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStand the tank upright and leave it to soak for a full seven minutes so the cotton draws liquid up through the base.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eTake two soft dry pulls with no power, then fire at low wattage and build up slowly.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the BVC Coil Box\u003c\/h2\u003e\n\u003cp\u003eInside: five \u003cstrong\u003eBVC\u003c\/strong\u003e coil heads in the resistance you selected, and that is it. No e-liquid, no tank, no battery. Every pack from Pirate Vapes arrives sealed with the scratch-and-check panel intact, so you can verify it is genuine before it goes near your tank.\u003c\/p\u003e\n\u003cp\u003eIf the tank body itself is worn rather than just the coil, you will want a fresh one from the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-tanks\" target=\"_blank\" title=\"Vape Tanks\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Tanks\u003c\/strong\u003e\u003c\/a\u003e range instead.\u003c\/p\u003e\n\u003ch2\u003eThe Right Coil for Aspire's Classic Clearomiser Tanks\u003c\/h2\u003e\n\u003cp\u003eThese heads belong to Aspire's clearomiser generation, and that is exactly where they fit. The \u003cstrong\u003eK1\u003c\/strong\u003e and \u003cstrong\u003eK2\u003c\/strong\u003e take them. So do the \u003cstrong\u003eCE5\u003c\/strong\u003e and \u003cstrong\u003eCE5-S\u003c\/strong\u003e. The \u003cstrong\u003eET\u003c\/strong\u003e and \u003cstrong\u003eET-S\u003c\/strong\u003e as well, along with other slim pen-style Aspire clearomisers from the same era. The Spryte and K-Lite are also compatible. If the coil sitting in your tank right now reads \u003cstrong\u003eBVC\u003c\/strong\u003e, you are in the right place.\u003c\/p\u003e\n\u003cp\u003eWhere they do not fit is anything newer. Aspire's \u003cstrong\u003eNautilus\u003c\/strong\u003e line, the \u003cstrong\u003eAtlantis\u003c\/strong\u003e and \u003cstrong\u003eTriton\u003c\/strong\u003e sub-ohm tanks, and the modern pod and mesh systems each run their own coil platforms, so a BVC head will not thread in or seal. When in doubt, hold the coil already in your tank against the pack, or browse the full \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/aspire-vapes\" target=\"_blank\" title=\"Aspire Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eAspire Coils\u003c\/strong\u003e\u003c\/a\u003e range for the correct fitment.\u003c\/p\u003e\n\u003ch2\u003eAbout Aspire\u003c\/h2\u003e\n\u003cp\u003eAspire built much of its early name on clearomiser hardware like the K-series and the CE5, the sort of kit that got a huge number of UK vapers away from cigarettes in the first place.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eBVC\u003c\/strong\u003e coil was a big part of that story, and Aspire still makes the genuine heads with the same scratch-and-check authenticity system on every box. For anyone running one of those original tanks, that consistency is the whole point. A real Aspire coil performs the same way today as the one that came in the kit years ago.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003eA pack of five is cheap insurance against a dead coil mid-week. At everyday \u003cstrong\u003eMTL\u003c\/strong\u003e use, you will change one roughly weekly, so five heads keep an old clearomiser going for over a month, far cheaper than replacing the whole kit.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e dispatches every order the same day before 4 pm through an age-verified checkout, over 18s only. Spend over £40 and delivery is on us with Free Pirate Post.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eIf you own one of Aspire's classic clearomiser tanks and it still does the job, there is no reason to bin it over a tired coil. A fresh five-pack of genuine \u003cstrong\u003eBVC\u003c\/strong\u003e heads brings the flavour straight back: three resistances, \u003cstrong\u003eorganic cotton\u003c\/strong\u003e, and easy low-wattage \u003cstrong\u003eMTL\u003c\/strong\u003e vaping that does exactly what it always did.\u003c\/p\u003e\n\u003cp\u003eGrab a few \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e on the same order and keep everything running. Shop the BVC coils today at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich tanks do BVC coils actually fit?\u003c\/h3\u003e\n\u003cp\u003eClassic Aspire clearomisers, so the K1, K2, CE5, CE5-S, ET and ET-S. They will not go in a Nautilus, Atlantis or any modern mesh tank. Check the coil in your tank: if it reads BVC, these are the ones.\u003c\/p\u003e\n\u003ch3\u003eCan I run nic salts through BVC coils?\u003c\/h3\u003e\n\u003cp\u003eYes. The tight MTL draw and low power suit salts at 10-20mg nicely. Just keep the liquid at a 50\/50 ratio rather than a thick salt blend.\u003c\/p\u003e\n\u003ch3\u003eHow long does one BVC coil last?\u003c\/h3\u003e\n\u003cp\u003eAround a week on daily MTL use. Lighter vapers might stretch it to ten days. Sweet liquids caramelise on the cotton faster, so those cut it shorter.\u003c\/p\u003e\n\u003ch3\u003eWhat BVC coil wattage should I start at?\u003c\/h3\u003e\n\u003cp\u003eLow. The 1.6ohm sits happily around 8-12W, the 1.2ohm likes a little more, the 1.8ohm a little less. Start at the bottom of the range and nudge up.\u003c\/p\u003e\n\u003ch3\u003eWhy does a new BVC coil taste weak or burnt?\u003c\/h3\u003e\n\u003cp\u003eAlmost always priming. If the cotton is not soaked before the first pull, it heats dry. Prime it, wait a good few minutes, take dry pulls, then fire. Thick juice and high wattage are the other usual culprits.\u003c\/p\u003e\n\u003ch3\u003eAre BVC genuine Aspire coils?\u003c\/h3\u003e\n\u003cp\u003eYes. Real Aspire heads with the scratch-and-check panel, not a third-party copy.\u003c\/p\u003e","brand":"Aspire","offers":[{"title":"1.2ohm","offer_id":52758712385818,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.6ohm","offer_id":52758712418586,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.8ohm","offer_id":52758712451354,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/Aspire_BVC_Replacement_Coil.jpg?v=1788015920","url":"https:\/\/piratevapes.co.uk\/products\/aspire-bvc-replacement-coils","provider":"Pirate Vapes","version":"1.0","type":"link"}