{"product_id":"geekvape-g-series-coils","title":"GeekVape G Series Coils","description":"\u003ch2\u003eGeekVape G Series Coils\u003c\/h2\u003e\n\u003cp\u003eSix resistances in one modular platform, all built for \u003cstrong\u003emouth-to-lung\u003c\/strong\u003e and restricted \u003cstrong\u003eDTL\u003c\/strong\u003e vaping. The \u003cstrong\u003eG coils\u003c\/strong\u003e are Geekvape's \u003cstrong\u003eKA-1 Kanthal mesh\u003c\/strong\u003e heads for its pod range, running from a punchy \u003cstrong\u003e0.6ohm at 13-18W\u003c\/strong\u003e down to a tight \u003cstrong\u003e1.8ohm at 7-9W\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eOrganic cotton sits under the mesh for steady wicking. They press straight into the pod base, no threading, no tools. Sold as a \u003cstrong\u003epack of 5\u003c\/strong\u003e, best matched with \u003cstrong\u003e50\/50\u003c\/strong\u003e blends or nic salts. If you run an Aegis Pod or a Wenax, these are the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-coils\" target=\"_blank\" title=\"Vape Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Coils\u003c\/strong\u003e\u003c\/a\u003e that keep it going.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy vapers choose this:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eOne coil family, six resistances so you can retune warmth, throat hit and vapour without buying a new device or hunting down a different coil line.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePress-fit means no threading and no tools. It pushes in.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eKA-1 Kanthal mesh heats evenly across the strip, which keeps flavour consistent and cuts down on hotspots and early dry hits.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eOrganic cotton wicks steadily at low wattage.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eFive to a pack, which covers most of a month for a daily vaper, depending on how sweet your liquid runs.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eGeekVape G Series Coils Features\u003c\/h2\u003e\n\u003ch3\u003ePress-Fit, Not Screw-In\u003c\/h3\u003e\n\u003cp\u003eNo threads on these. You lift the spent coil out of the pod base and push a fresh one in until it seats, and that friction fit is the whole install. Less mess, no cross-threading, and a swap you can do one-handed. Handy when you are topping up on the move rather than sat at a desk.\u003c\/p\u003e\n\u003ch3\u003eWhy Does the Mesh Run Cooler Than It Looks?\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003emesh strip\u003c\/strong\u003e spreads heat over a wider surface than a round wire, so even the low \u003cstrong\u003e0.6ohm\u003c\/strong\u003e never turns harsh at \u003cstrong\u003e13-18W\u003c\/strong\u003e. You get vapour and warmth without the scorched edge. Fair enough if cheap coils have burned you before. This build earns its flavour.\u003c\/p\u003e\n\u003ch3\u003eThat Low-Wattage Sweet Spot\u003c\/h3\u003e\n\u003cp\u003eEvery resistance here tops out under \u003cstrong\u003e18W\u003c\/strong\u003e. The \u003cstrong\u003e1.0ohm\u003c\/strong\u003e at \u003cstrong\u003e10-12W\u003c\/strong\u003e and the \u003cstrong\u003e1.2ohm\u003c\/strong\u003e at \u003cstrong\u003e9.5-11.5W\u003c\/strong\u003e barely touch a pod battery, so you charge less, and the coil lasts longer. Pair them with \u003cstrong\u003eNic Salts\u003c\/strong\u003e at 10 or 20mg for a smooth, satisfying hit.\u003c\/p\u003e\n\u003ch3\u003eBuilt Around Organic Cotton\u003c\/h3\u003e\n\u003cp\u003eUnder the mesh sits \u003cstrong\u003eorganic cotton\u003c\/strong\u003e wicking. It pulls \u003cstrong\u003e50\/50\u003c\/strong\u003e and higher-PG liquid through steadily at these low powers, which is what keeps the taste clean from the first pull to the last. Thicker high-VG juice will not feed properly, so keep the liquid thin.\u003c\/p\u003e\n\u003ch3\u003eTwo Takes on 1.2ohm\u003c\/h3\u003e\n\u003cp\u003eWorth knowing before you pick. There are two \u003cstrong\u003e1.2ohm\u003c\/strong\u003e heads. The standard one runs \u003cstrong\u003e9.5-11.5W\u003c\/strong\u003e for a classic tight MTL draw. The \u003cstrong\u003e1.2ohm S\u003c\/strong\u003e shifts the window to \u003cstrong\u003e8-12W\u003c\/strong\u003e, opening it up a fraction at the bottom. Small difference, but it changes how warm the pull feels.\u003c\/p\u003e\n\u003ch2\u003eGeekVape G Series Coils Resistance Options\u003c\/h2\u003e\n\u003cp\u003eSix heads in the picker, all mesh, all low wattage. The right one comes down to how tight you want the draw and how strong your liquid is.\u003c\/p\u003e\n\u003cp\u003eMost popular: the \u003cstrong\u003e0.8ohm\u003c\/strong\u003e at \u003cstrong\u003e12-15W\u003c\/strong\u003e. It sits in the middle of the range, cool enough for smooth all-day salts and open enough to give a touch more vapour than the higher resistances. Unsure where to begin? Start here.\u003c\/p\u003e\n\u003cp\u003eWarmest and airiest: the \u003cstrong\u003e0.6ohm\u003c\/strong\u003e at \u003cstrong\u003e13-18W\u003c\/strong\u003e. This is the restricted-DTL end, more vapour, a looser pull. It works best with lower-strength \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/50-50-e-liquids\" target=\"_blank\" title=\"50\/50 E-Liquids\" rel=\"noopener\"\u003e\u003cstrong\u003e50\/50 E-Liquids\u003c\/strong\u003e\u003c\/a\u003e around 10mg.\u003c\/p\u003e\n\u003cp\u003eFor a tighter draw, the \u003cstrong\u003e1.0ohm\u003c\/strong\u003e at \u003cstrong\u003e10-12W\u003c\/strong\u003e steps things in, and the \u003cstrong\u003e1.2ohm\u003c\/strong\u003e at \u003cstrong\u003e9.5-11.5W\u003c\/strong\u003e goes tighter still for a proper cigarette-style MTL pull on stronger salts. The \u003cstrong\u003e1.2ohm S\u003c\/strong\u003e runs \u003cstrong\u003e8-12W\u003c\/strong\u003e if you want that same tightness with a little less heat.\u003c\/p\u003e\n\u003cp\u003eTightest and coolest: the \u003cstrong\u003e1.8ohm\u003c\/strong\u003e at \u003cstrong\u003e7-9W\u003c\/strong\u003e. Least vapour, most discreet, and the longest-lasting of the set on 20mg salts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e#buttons\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e0.6ohm\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e0.8ohm\u003c\/li\u003e\n\u003cli\u003e1.0ohm\u003c\/li\u003e\n\u003cli\u003e1.2ohm\u003c\/li\u003e\n\u003cli\u003e1.2ohm S\u003c\/li\u003e\n\u003cli\u003e1.8ohm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eHow to Set Up the GeekVape G Series Coils\u003c\/h2\u003e\n\u003cp\u003eQuick job. A couple of minutes, no tools.\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cp\u003eLift the old coil out of the base of your pod. It pulls straight out.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eDrip three or four drops of e-liquid onto the exposed cotton of the new coil and into the wicking ports on its side.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003ePush the fresh coil into the pod base until it seats with a firm click.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eRefill the pod with your 50\/50 or nic salt liquid and close the fill port.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStand the filled pod upright and leave it a full five minutes so the cotton drinks all the way through before you fire it.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eStart at the low end of that coil's wattage and take a few soft pulls before working up.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eWhat's in the GeekVape G Series Coils Box\u003c\/h2\u003e\n\u003cp\u003eFive \u003cstrong\u003eG coils\u003c\/strong\u003e in the single resistance you select. That is the lot. No pod, no device, and no e-liquid in the pack. If the pod itself is worn or cracked, you will want a replacement pod rather than just a coil, since the coil seats inside it.\u003c\/p\u003e\n\u003ch2\u003eMade for Geekvape's Aegis Pod and Wenax Range\u003c\/h2\u003e\n\u003cp\u003eThese heads are a Geekvape pod-specific coil, so fitment is limited to the devices built around the G.Coil platform. They drop into the original \u003cstrong\u003eAegis Pod\u003c\/strong\u003e and the newer \u003cstrong\u003eAegis Pod 2\u003c\/strong\u003e. The \u003cstrong\u003eWenax Stylus\u003c\/strong\u003e takes them. So does the \u003cstrong\u003eWenax C1\u003c\/strong\u003e, along with the \u003cstrong\u003eG18\u003c\/strong\u003e pen kit. Browse the wider \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/geekvape-vapes\" target=\"_blank\" title=\"Geekvape Pod Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eGeekvape Pod Kits\u003c\/strong\u003e\u003c\/a\u003e if you still need the matching device.\u003c\/p\u003e\n\u003cp\u003eWhat they will not fit: Geekvape's sub-ohm tank coils are a different platform. The Zeus and Z-series mesh heads do not cross over. Neither do the B and P series boost coils. If your current coil is stamped with a G and pushes in rather than screwing, you are in the right place. Every G coil sold at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e is matched to the pod range above.\u003c\/p\u003e\n\u003ch2\u003eAbout Geekvape\u003c\/h2\u003e\n\u003cp\u003eGeekvape built its name on rugged, well-engineered hardware, and the G coil shows the same thinking. Rather than a fresh coil for every pod, the brand designed the \u003cstrong\u003eG.Coil platform\u003c\/strong\u003e as a modular standard: one press-fit format that carries across the Aegis Pod line and the Wenax kits. A single coil range covers several devices, so stock stays simple and you are not chasing a different head every time you upgrade.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003eKA-1 mesh\u003c\/strong\u003e build brings the flavour-first engineering Geekvape runs across its coils. If you are still choosing a home for them, the \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/mtl-vape-kits\" target=\"_blank\" title=\"MTL Vape Kits\" rel=\"noopener\"\u003e\u003cstrong\u003eMTL Vape Kits\u003c\/strong\u003e\u003c\/a\u003e range is where these coils feel right.\u003c\/p\u003e\n\u003ch2\u003eStock Up and Save\u003c\/h2\u003e\n\u003cp\u003eA single G coil runs a week or two of daily MTL vaping before the flavour drops off, and sweeter liquids burn through faster. A \u003cstrong\u003epack of five\u003c\/strong\u003e covers most of a month, and grabbing two packs means you are never caught short mid-week.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePirate Vapes\u003c\/strong\u003e dispatches same day on orders placed before 4 pm, so a fresh set lands quickly. All stock is \u003cstrong\u003eTPD compliant\u003c\/strong\u003e, sold through an \u003cstrong\u003eage-verified checkout\u003c\/strong\u003e, and \u003cstrong\u003eover-18s only\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eConclusion\u003c\/h2\u003e\n\u003cp\u003eThe G coils are a simple, sensible replacement for anyone running a Geekvape Aegis Pod or Wenax. Six resistances from \u003cstrong\u003e0.6ohm\u003c\/strong\u003e to \u003cstrong\u003e1.8ohm\u003c\/strong\u003e let you dial the draw from restricted DTL to tight MTL, the \u003cstrong\u003emesh\u003c\/strong\u003e build keeps flavour clean, and press-fit fitting makes swaps painless.\u003c\/p\u003e\n\u003cp\u003eMatch the resistance to your liquid strength, and they will serve you well. Stock more \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/geekvape-coils\" target=\"_blank\" title=\"Geekvape Coils\" rel=\"noopener\"\u003e\u003cstrong\u003eGeekvape Coils\u003c\/strong\u003e\u003c\/a\u003e, pair them with fresh \u003ca href=\"https:\/\/piratevapes.co.uk\/collections\/vape-accessories\" target=\"_blank\" title=\"Vape Accessories\" rel=\"noopener\"\u003e\u003cstrong\u003eVape Accessories\u003c\/strong\u003e\u003c\/a\u003e, or start at \u003cstrong\u003ePirate Vapes\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch2\u003eFAQs\u003c\/h2\u003e\n\u003ch3\u003eWhich devices do the G coils fit?\u003c\/h3\u003e\n\u003cp\u003eThe Geekvape Aegis Pod and Aegis Pod 2, the Wenax Stylus, the Wenax C1, and the G18 pen. They will not fit Geekvape's sub-ohm tanks or boost-coil pods.\u003c\/p\u003e\n\u003ch3\u003eAre the G coils mesh?\u003c\/h3\u003e\n\u003cp\u003eYes. Every resistance in the range uses a KA-1 Kanthal mesh strip for even heating.\u003c\/p\u003e\n\u003ch3\u003eWhich resistance should I start with the G coils?\u003c\/h3\u003e\n\u003cp\u003eThe 0.8ohm at 12-15W is the safest all-rounder. Go lower to 0.6ohm for more vapour, or higher to 1.2ohm and 1.8ohm for a tighter, cigarette-style draw on stronger salts.\u003c\/p\u003e\n\u003ch3\u003eWhat e-liquid works best with the G coils?\u003c\/h3\u003e\n\u003cp\u003e50\/50 blends and nic salts. These are low-wattage MTL coils, so thick high-VG juice will not wick properly and risks dry hits.\u003c\/p\u003e\n\u003ch3\u003eHow long does a G coil last?\u003c\/h3\u003e\n\u003cp\u003eRoughly one to two weeks on daily use. Sweeter, darker liquids shorten that as residue builds on the cotton faster.\u003c\/p\u003e\n\u003ch3\u003eDo I need to prime the G coils?\u003c\/h3\u003e\n\u003cp\u003eYes, always. Drip a few drops onto the cotton, fill, then wait five minutes before firing. Skip that step, and you scorch the coil straight away.\u003c\/p\u003e","brand":"Geekvape","offers":[{"title":"0.6ohm","offer_id":52755397509402,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"0.8ohm","offer_id":52755397542170,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.0ohm","offer_id":52755397574938,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.2ohm","offer_id":52755397607706,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.2ohm S","offer_id":52755397640474,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true},{"title":"1.8ohm","offer_id":52755397673242,"sku":null,"price":6.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0995\/5675\/3690\/files\/GeekVape_G_Series_Coils.jpg?v=1787986015","url":"https:\/\/piratevapes.co.uk\/products\/geekvape-g-series-coils","provider":"Pirate Vapes","version":"1.0","type":"link"}