SMOK IGEE Pro Replacement Pods

A 2ml refillable pod with a 0.9ohm mesh coil sealed inside, built for SMOK's compact IGEE range. The SMOK IGEE Pro pods use a magnetic connection that clicks into the device without any threading or force, and a top-fill system that opens by removing the mouthpiece. 

Three pods per pack. Each one runs at MTL resistance and pairs with 50/50 or nic salt e-liquids between 10mg and 20mg. Leak-resistant design throughout. No coil swapping, no maintenance beyond filling and replacing. When the flavour drops off, pull the old pod out and push a fresh one in. 

Over 18s only. Browse the full range of SMOK Devices at Pirate Vapes.

Why vapers choose this:

• Zero coil maintenance means no unscrewing, no priming individual coils, and no guessing which replacement fits. The coil is inside the pod. When it is done, the whole pod goes.

• Mesh heating at 0.9ohm delivers more even heat distribution than a standard round-wire coil, which means sharper flavour and fewer dull spots towards the end of the coil's life

• Magnetic connection makes swapping pods faster than any threaded or press-fit system, and it holds firm in a pocket without rattling loose

• Top fill through the mouthpiece keeps your hands and your device cleaner than side-fill ports

• Three per pack covers a couple of weeks for most daily MTL vapers, sometimes longer with lighter use

SMOK IGEE Pro Replacement Pods Features

Why Sealed Coils Make Sense for This Device

The IGEE pods do not use removable coils. The mesh element is built into the pod body permanently, and the whole unit gets replaced when flavour quality drops. For a compact, low-wattage MTL kit like the IGEE Pro, that trade-off works. 

You lose the ability to swap just the coil, but you gain a pod that never leaks around a loose coil seat and never needs you to carry a coil toolkit. Practically speaking? Less fiddling, cleaner pockets.

Mesh at 0.9ohm Hits Differently

Most mesh coils sit below 0.5ohm and run at high wattage for cloud production. The IGEE pod flips that. A 0.9ohm mesh element running at 8 to 12W gives you the even heating benefits of mesh, but at MTL power levels. 

The result is flavour that stays consistent across the pod's lifespan without the heat or vapour volume of a sub-ohm setup. If you vape nic salts at 10mg or 20mg, the low wattage keeps the throat hit smooth rather than harsh.

That Top-Fill System

Pull off the mouthpiece. There is a fill port underneath. Tilt your bottle nozzle into the port, fill to just below the max line, and press the mouthpiece back on. The central hole is the airway chimney, not a fill point. 

Worth mentioning because filling through the wrong hole floods the coil and creates a gurgling mess. Stick to the side port. Fair enough; it can be a little stiff to remove at first, but it loosens with use.

Magnetic Snap and Go

The pod drops into the IGEE A1 or IGEE Pro body and magnets hold it in place. No twisting, no clicking. Pull upward to remove, push down to install. The magnet strength keeps the pod stable during use and transit, and the alignment is consistent every time. 

That matters more than it sounds, because a misaligned pod means poor electrical contact and weak or inconsistent vapour.

Leak-Resistant Build

SMOK's leak-resistant pod design keeps liquid sealed inside the PCTG housing and away from the battery contacts. The top-fill port sits under the mouthpiece rather than on the side, which reduces the chance of accidental opening in a pocket. Not every pod kit gets this right, and a leaking pod ruins the draw, wastes liquid, and can damage the device over time.

SMOK IGEE Pro Replacement Pods Compatibility

The MTL Pod for SMOK's IGEE Range

Two devices use this pod: the SMOK IGEE A1 and the SMOK IGEE Pro. Both are compact, lightweight, MTL Vape Kits built for daily nic salt use. The A1 runs at a fixed 14W output with draw activation. The Pro adds a 0.69-inch OLED screen, five power modes between 8W and 12W, and a button-fire option.

Same pod in both devices. Same magnetic fit. If you own either kit, this is the only Replacement Pod you need.

These pods do not fit any other SMOK device. Not the Novo range. Not the Nord family. Not the RPM series. Each of those platforms uses its own pod format with different dimensions, coil types, and connection systems.

How to Set Up the SMOK IGEE Pro Replacement Pods

Simple swap. Two minutes at most.

1. Pull the spent pod straight up and out of the IGEE device. The magnets release with a gentle tug.

2. Take a fresh pod from the pack. Remove the mouthpiece by lifting it upward from the pod body.

3. Drip three to four drops of e-liquid directly onto the exposed cotton visible inside the pod. This pre-saturates the mesh before the first fill.

4. Tilt your e-liquid bottle into the side fill port (not the central airway hole) and fill to just below the max line. Press the mouthpiece firmly back into place.

5. Push the pod into the IGEE device until the magnets snap it into position. Leave it standing upright for five minutes without drawing. The mesh cotton needs time to absorb liquid fully from the reservoir, and firing the device before saturation burns the wick permanently.

6. Take two or three gentle draws without pressing the fire button to help pull liquid into the coil. Then start vaping at the lowest power setting.

What's in the SMOK IGEE Pro Replacement Pods Box

Three SMOK IGEE replacement pods, each with a 2ml capacity and a pre-installed 0.9ohm mesh coil. Mouthpieces fitted. No e-liquid included. No device, no cable, no extras. Just the pods.

If you do not already own a compatible device, the Refillable Pod Kits collection has the IGEE Pro and other MTL options to pair with these pods.

About SMOK

SMOK has been manufacturing vape hardware since 2010, and the product range now spans everything from compact pod systems to high-wattage box mods. The IGEE line sits at the simplest end of the catalogue: small zinc-alloy bodies, sealed-coil pods, and low power output designed for MTL vapers who want a clean draw without any complexity. 

Where SMOK's Novo and Nord families offer swappable coils and adjustable airflow, the IGEE strips that back to a single-coil pod and a magnetic connection. Less to go wrong, less to think about. That simplicity is the point, and for vapers who just want to fill, vape, and replace, the platform delivers. 

Browse more from SMOK at Pirate Vapes.

Stock Up and Save

Three pods per pack. Daily MTL vapers will burn through one pod every five to seven days depending on how heavily they vape and how sweet their liquid runs. Picking up two packs at once keeps you covered for over a month without any last-minute scrambling when the flavour starts to fade. 

Every order from Pirate Vapes ships the same day before 4 pm, padded and tracked. TPD compliant, age-verified checkout, over-18s only. Spend over £40 and delivery is on us with Free Pirate Post.

Conclusion

The SMOK IGEE Pro replacement pods do one thing well: deliver consistent MTL flavour from a sealed mesh coil in a compact, leak-resistant housing. No coil changes, no threading, no maintenance beyond filling and replacing. 

Three per pack, 2ml capacity, 0.9ohm mesh, magnetic connection, and compatibility with both the IGEE A1 and IGEE Pro kits. If your IGEE device needs a fresh pod, this is the only option, and it works exactly as it should. 

Pick up a pack at Pirate Vapes and check the Vape Accessories collection for everything else your setup needs.

FAQs

Which devices do the IGEE pods fit?

The SMOK IGEE A1 and the SMOK IGEE Pro. Both use the same pod with the same magnetic connection. No other SMOK device is compatible.

What e-liquid works best with the IGEE pods?

50/50 VG/PG nic salts at 10mg or 20mg. The 0.9ohm coil runs at low wattage and produces a tight MTL draw, which suits thinner liquids. High-VG blends will not wick properly and will cause dry hits.

How long does each IGEE pod last?

Five to seven days of regular daily use. Sweeter liquids gunk up the mesh faster, so if you vape dessert or candy profiles, expect closer to four or five days.

Can I replace just the coil inside the SMOK IGEE Pro pod?

No. The coil is permanently sealed inside the pod housing. When the flavour degrades, you replace the entire pod with a fresh one from the pack.

How do I fill the IGEE pods without flooding them?

Remove the mouthpiece and fill through the side port only. The central hole is the airway chimney. Filling through it floods the coil, causes gurgling, and wastes your liquid. Keep the nozzle angled into the side port and fill slowly.

Are the IGEE pods MHRA notified?

Yes. The SMOK IGEE pods carry GBID 03862-22-00328 on the MHRA Notified Products List.