Oxva Xlim V3 Top Fill Replacement Pods 

Three pods per pack, four resistances to choose from, and compatibility with practically every device OXVA has released under the XLIM name. The OXVA Xlim Top Fill pods hold 2ml each under UK TPD rules, use Unitech 2.0 mesh coils for consistently clean flavour, and refill from the top in a few seconds.

Resistances run from 0.4ohm for restricted direct lung draws right through to 1.2ohm for a tight, cool mouth-to-lung pull. Magnetic connection clicks into every OXVA Device in the XLIM family. Over 18s only.

Why vapers choose these pods:

• Unitech 2.0 mesh inside every pod delivers noticeably sharper flavour and roughly 30% longer coil life compared to standard pod builds

• Top fill in about three seconds. Open the plug, squeeze in your liquid, close it. No pod removal needed, no disassembly.

• Five-layer leak-proof construction tested across 200+ puffing simulations and 30+ liquid compatibility checks. Your pockets stay dry.

• Four resistances covering MTL and RDTL means you pick the draw style, not the other way around

• Magnetic connection clicks the pod firmly into every XLIM-series device without wobble or misalignment

OXVA Xlim Top Fill Pods Features

Unitech 2.0 Is Not Just a Name on the Box

OXVA's Unitech 2.0 system uses a multi-layer cotton arrangement with engineered oil channels inside each mesh coil. The cotton is structured so that liquid reaches the mesh heating element more evenly and faster than in a standard pod coil. The result is noticeable: flavour stays consistent from the first fill through to the end of the coil's life rather than peaking early and then slowly degrading. OXVA claims roughly 50% better flavour restoration and 30% longer coil lifespan than their previous generation. That tracks with real-world use, honestly.

Five Layers Between Your Liquid and Your Pocket

Leaking pods ruin devices, ruin pockets, and ruin the whole experience. OXVA built a five-layer seal structure into the XLIM Top Fill pods and tested it against over 200 puffing behaviour simulations, 30+ e-liquid formulations, and five different environmental stress conditions.

The silicone top fill plug, the internal pod seals, and the base connection all work together. Not a guarantee that nothing will ever leak under any circumstance, but it is one of the more thoroughly tested Replacement Pod designs on the market.

Top Fill That Actually Works Quickly

Some top fill designs are fiddly. The XLIM pods are not. The silicone plug opens easily, the fill port is wide enough for most bottle nozzles, and there is enough space inside to fill without air bubbles forcing liquid back out. Three seconds is realistic, not marketing. You can refill without removing the pod from the device if you prefer, though removing it first gives you a cleaner angle.

Cross-Compatible With the Entire XLIM Range

One pod platform across more than a dozen devices. That is a deliberate choice OXVA made years ago, and it continues to pay off for anyone invested in the ecosystem. Bought a pack of 0.8ohm pods for your Xlim Go? They also fit the Xlim Pro 2, the Xlim SQ Pro 2, the Xlim Classic Edition, and every other XLIM device. Your pod stock travels with you if you upgrade, downgrade, or keep a second device as backup.

Four Resistances, Four Completely Different Draws

The difference between the 0.4ohm at 26 to 30W and the 1.2ohm at 10 to 12W is enormous. It is not a subtle tweak. The 0.4 produces genuine RDTL clouds with warmth and density. The 1.2 delivers a very tight, cool draw that feels close to a cigarette. The 0.6 and 0.8 sit between those two ends, and either works well as a daily driver for most vapers. Having all four available means you can experiment without needing a different device.

OXVA Xlim Top Fill Pods Resistance Options

Four mesh coil options, each designed for a specific vaping style. The right choice depends on your preferred draw, nicotine strength, and how you like your vapour.

The 0.8ohm is the most widely used. Running at 12 to 16W, it delivers a comfortable MTL draw with a solid throat hit. Pair it with 50/50 nic salts at 10mg or 20mg, and it performs exactly as you would expect from a dedicated mouth-to-lung pod. If you are switching from disposables or cigarettes, this is the resistance to start with.

For a slightly looser draw, the 0.6ohm sits in interesting territory between MTL and RDTL. At 20 to 25W, it produces more vapour than the 0.8 without losing the flavour clarity. Works well with 50/50 nic salts at 10mg or freebase at 6mg to 12mg. A genuine all-rounder.

The 0.4ohm is the cloud chaser in the lineup. At 26 to 30W, it runs warm and produces dense, flavourful vapour. Best paired with lower-strength freebase liquid at 3mg to 6mg or nic salt at 10mg maximum. Not every XLIM device supports the wattage this pod needs, so check your device first. The Xlim Pro, Xlim Pro 2, Xlim SQ Pro, and Xlim Go are all confirmed compatible.

The 1.2ohm is the tightest draw available. Running at just 10 to 12W, it barely touches battery life and produces minimal vapour. Ideal for nic salts at 10mg to 20mg where you want the satisfaction without the cloud. Very low liquid consumption too, so each fill stretches further.

#buttons

• 0.4ohm
• 0.6ohm
• 0.8ohm
• 1.2ohm

How to Set Up the OXVA Xlim Top Fill Pods

Fast process. Two minutes from pack to first draw if you do not rush the priming.

1. Take a fresh pod from the pack and remove any protective caps or silicone covers from the mouthpiece and base contacts.

2. Peel open the top fill plug. It is a small silicone flap on the top of the pod. Lift it gently rather than yanking it, so the seal stays intact for future refills.

3. Tilt your e-liquid bottle into the fill port at a slight angle. Fill to just below the max line with a 50/50 or higher-PG liquid. Keep the nozzle clear of the central air channel.

4. Press the fill plug closed firmly and wipe any stray liquid from the pod surface.

5. Leave the filled pod standing upright for five to seven minutes without inserting it into your device. The multi-layer Unitech cotton needs adequate time to absorb liquid from top to bottom through those engineered oil channels. Firing the pod before the wick is fully saturated will burn the mesh and ruin the flavour permanently.

6. Click the pod into your XLIM device (the magnetic connection seats it in one motion) and take two or three gentle draws to confirm the coil is primed. You are good to go.

What's in the OXVA Xlim Top Fill Pods Box

Three pods per pack, all in your selected resistance. No e-liquid, no device, no coils. The coil is sealed inside each pod permanently, so there are no loose parts to handle or install. If you need e-liquids to go with these pods, browse the nic salt and 50/50 collections for compatible options.

The Pod That Fits Every XLIM Device You Own

The XLIM Top Fill pod is cross-compatible across the full XLIM family. That includes the Xlim Pro, Xlim Pro 2, Xlim SQ Pro, Xlim SQ Pro 2, Xlim Go, Xlim Go 2, Xlim Go Lite, Xlim SE, Xlim SE 2, Xlim Classic Edition, and the Xlim 3 Ultra. The Dovpo Ayce Mini and Ayce Pro also accept these pods, since those devices use the same XLIM pod connection.

One important note: the 0.4ohm pod requires 26 to 30W to fire correctly. Not all XLIM devices reach that wattage. The Xlim Go Lite, for example, maxes out at 30W, so it will work, but entry-level XLIM devices with lower wattage caps may not provide enough power for the 0.4. If your device tops out below 26W, stick with the 0.6ohm, 0.8ohm, or 1.2ohm pods. Browse the full OXVA pod range for all available options.

About OXVA

OXVA's approach to pod design centres on one idea: build the coil platform once, build it well, and make it work across every device in the family. The Unitech coil system is the core of that strategy. Rather than creating a new pod format for each device release, OXVA invested in refining the mesh structure, cotton layering, and sealing technology inside a single pod shell that fits them all.

The XLIM pod has been recognised by reviewers and industry awards for flavour delivery and durability, and the cross-device compatibility gives XLIM owners a single consumable to stock regardless of which device they carry.

Stock Up and Save

Pods are the one thing you will always need more of. Three per pack, and at daily MTL use, you will go through one every week to two weeks depending on how heavily you vape. Setting up a recurring order through The Crow's Nest means fresh pods arrive on your schedule without reordering each time.

Every order from Pirate Vapes ships the same day before 4 pm. TPD compliant, age-verified checkout, over 18s only. Free Pirate Post on orders over £25.

Conclusion

The XLIM Top Fill pods do what good replacement pods should: deliver clean flavour, refill quickly, seal properly, and fit every device in the ecosystem without guesswork. Four resistances cover the full range from tight MTL at 1.2ohm through to genuine RDTL clouds at 0.4ohm, and the Unitech 2.0 mesh inside each pod genuinely extends coil life compared to standard builds.

If you own any XLIM device, these are the pods it was designed around. Browse more Refillable Pod Kits, pick up some Vape Accessories, or head back to Pirate Vapes for the full range.

FAQs

How many OXVA Xlim pods come in a pack?

Three. All in the same resistance. Pick your preferred ohm level when ordering.

Which XLIM devices do these pods fit?

Every one. The Xlim Pro, Pro 2, SQ Pro, SQ Pro 2, Go, Go 2, Go Lite, SE, SE 2, Classic Edition, 3 Ultra, and the Dovpo Ayce Mini and Ayce Pro. Magnetic connection is identical across the range.

What e-liquid works best with the Xlim pods?

50/50 VG/PG blends and nic salts. Higher-PG formulas also wick well. Avoid high-VG liquids above 60% VG, as the wicking ports are sized for thinner liquids and thick juice causes dry hits.

Can I use 20mg nic salts in the OXVA Xlim 0.4ohm pod?

You can physically, but it will be uncomfortably strong. 20mg nic salt at 26 to 30W through a low-resistance mesh coil delivers a very intense hit. Stick to 3mg to 6mg freebase or 10mg nic salt maximum with the 0.4ohm. Save 20mg for the 0.8ohm or 1.2ohm pods.

How long does each OXVA Xlim pod last?

Depends on resistance and usage. The 0.8ohm typically lasts one to two weeks at moderate daily MTL vaping. The 1.2ohm can stretch beyond two weeks with light use. The 0.4ohm runs hotter and tends to last five to ten days. You will know it is time to replace when the flavour turns flat or slightly burnt.

Are these the same as XLIM EZ pods?

No. The XLIM Top Fill pods have a sealed, permanent coil. The XLIM EZ pods are a separate format with a different internal design. Both fit the same XLIM devices, but they are not interchangeable mid-use. Choose one format and stock accordingly.