OXVA Nexlim Replacement Pods

Two mesh strips per pod, not one. Every OXVA NeXlim replacement pod carries a built-in dual mesh coil that heats your liquid across a wider surface than single-mesh alternatives. Three resistances, each colour-coded at the base, so you can grab the right one from your drawer without reading fine print. Black for 0.6 ohm. Orange for 0.8 ohm.

Green for 1.2 ohm. Sold in 3-packs, 2ml TPD capacity, with a top-fill port that opens without removing the pod from the device. UNITECH 2.0 technology inside every coil. Pirate Vapes stocks all three resistances. TPD compliant. Over 18s only.

Why vapers choose OXVA Nexlim Replacement Pods:

• Dual mesh means two heating surfaces, not one. Each pod fires two mesh strips at the same time. More liquid gets heated per puff, which translates to fuller flavour and visibly denser vapour compared to single-mesh pod kits at the same wattage.

• Colour-coded bases identify resistance at a glance. Black for the open 0.6. Orange for the crossover 0.8. Green for the tight 1.2. No squinting at tiny text on the pod when you reach into your drawer.

• Five-layer sealed construction handles daily carry. Triple silicone seals, a bottom-mounted coil, and a reinforced body work together to keep liquid inside the pod. Most users report no leaking across the full life of each pod.

• 2-3 weeks per pod is genuine. Independent testing measured 15-20 refills before flavour noticeably drops. That is weeks of daily use from each pod in the 3-pack.

• Top-fill without pulling the pod out. Peel back the rubber stopper, add liquid, close it. The pod stays in the device the entire time. No drips on the contacts, no re-seating issues.

OXVA Nexlim Replacement Pods Features

UNITECH 2.0 Dual Mesh Coil

Two mesh strips sit side by side inside every NeXlim pod. They fire together, heating liquid across roughly double the surface area of a single-mesh pod. OXVA rates this at 200% better flavour and 200% longer coil life compared to their single-mesh coils. The practical difference: flavour stays strong deeper into each pod's lifespan, and you change pods less often.

Five-Layer Leak-Resistant Construction

Three silicone seals at the fill port, base, and contact points. The coil sits at the bottom of the pod, keeping liquid above it rather than pooling around the contacts. The pod body itself is reinforced to prevent flex. The five layers work together so that overfilling is the only realistic cause of any moisture at the base. Wipe it, do not overfill, and the pods stay clean.

Colour-Coded Base for Instant Resistance Identification

Black base: 0.6 ohm. Open RDTL draw at 20-40W. Orange base: 0.8 ohm. MTL/RDTL crossover at 12-32W. Green base: 1.2 ohm. Tight MTL at 10-25W. The colour is visible at the bottom of the pod whether it is in or out of the device. If you keep multiple resistances in stock, the colour coding eliminates mistakes.

Top-Fill Port with Rubber Stopper

The fill port sits on the side near the top of the pod. Peel back the rubber stopper, angle your bottle in, fill to the line, and press the stopper shut. The pod does not need to come out of the device. The stopper creates a firm seal that holds during pocket carry. No open ports, no exposed holes.

Transparent Pod Body with Clear Liquid Windows

Both sides of the pod show your liquid level through the transparent PCTG material. You can tell when to refill without removing the pod or guessing. When the liquid drops below the coil intake windows, top it up. This visibility also helps you spot discolouration in the liquid, which signals the coil is nearing the end of its life.

OXVA Nexlim Replacement Pods Resistances List

Three resistances, each colour-coded and designed for a different draw style. The 0.8-ohm orange base is the bestseller and the pod most NeXlim owners settle on. The 0.6-ohm suits vapers who prefer warmer, cloudier pulls. The 1.2-ohm is for tight MTL vapers who want a draw as close to a cigarette as a pod kit can deliver.

Bestseller:

• 0.8 Ohm (Orange Base), RDTL and MTL: The crossover pod. Works with nic salts at a firm MTL draw or opens up into lighter RDTL territory. 12-32W. The most popular resistance in the range

Open Draw:

• 0.6 Ohm (Black Base), RDTL: Warmer vapour, more visible cloud, open draw. Handles 70/30 VG as well as 50/50. 20-40W

Tight Draw:

• 1.2 Ohm (Green Base), MTL: The tightest pull in the NeXlim range. Cool, firm, cigarette-style draw. Best with 20mg nic salt at 10-25W

How to Set Up the OXVA Nexlim Replacement Pods

1. Unpack. Take a fresh pod from the 3-pack. Check the base colour matches the resistance you want.

2. Fill. Peel back the rubber stopper near the top of the pod. Squeeze your e-liquid in up to the 2ml line. Leave a small air gap at the top. Press the stopper firmly back into place.

3. Prime. Let the filled pod sit upright for five to ten minutes. The dual mesh coils need time to soak. Skipping this step can burn the cotton on the first draw.

4. Remove the old pod. Pull the spent pod from your NeXlim device and discard it.

5. Insert. Push the new pod into the device. The magnets click it securely into place. The screen wakes and shows the detected resistance.

6. Adjust. Select Boost or Eco mode on the device. Adjust the airflow slider. The device auto-sets the wattage for the installed pod.

7. Vape. Inhale through the mouthpiece. The NeXlim fires on auto-draw.

What's in the OXVA Nexlim Replacement Pods Box

Each pack contains three identical pods at your chosen resistance. Every pod has a built-in UNITECH 2.0 dual mesh coil sealed inside, a 2ml capacity, a transparent PCTG body, a colour-coded base, and magnetic contacts. No device, no e-liquid, no cable. The pods are the only contents.

Designed Exclusively for the OXVA NeXlim Range

NeXlim pods only fit NeXlim devices. They are not cross-compatible with the Xlim range or any other OXVA product.

Compatible:

• OXVA NeXlim: 1500mAh, 40W, Boost/Eco modes, colour screen. The original NeXlim kit

• OXVA NeXlim Go: Compact version with a smaller battery

• OXVA NeXlim 2: Upgraded with UNITECH 3.0 pods (also accepts 2.0), 2000mAh battery

• OXVA NeXlim 2 Mini: Compact version of the NeXlim 2

Not Compatible (different pod platform entirely):

• Any OXVA Xlim device: Pro, Pro 2, Pro 3, SE, SQ Pro, Go, V3, Nano, etc.

• OXVA Oneo

• Any non-OXVA device

If you own an Xlim device, you need Xlim pods, not NeXlim pods. Check the Pirate Vapes Replacement Pods collection for the correct match.

About OXVA

OXVA launched in 2018 and the NeXlim range is their dual mesh pod platform, separate from the single-mesh Xlim line. The two families share a similar body shape but use different pod formats and different coil technology. UNITECH 2.0 in the NeXlim fires two mesh strips per pod for wider heating coverage.

The NeXlim range now spans four devices (NeXlim, NeXlim Go, NeXlim 2, NeXlim 2 Mini), and every pod works in every NeXlim device. Browse the full OXVA Vapes collection at Pirate Vapes.

Stock Up and Save

Three resistances, three colour-coded bases, one 3-pack per order. At Pirate Vapes, we stock all three NeXlim pod options so you can grab your preferred resistance alongside your liquid in one order. Every pod is TPD compliant, MHRA-notified, and factory-sealed. We verify stock before listing and ship tracked in secure packaging. If a pod arrives faulty or damaged, we sort the replacement the same day. Free Pirate Post on orders over £25.

Conclusion

Dual mesh. Colour-coded. Five-layer sealed. 2-3 weeks per pod. The OXVA NeXlim replacement pods deliver on the dual mesh promise with fuller flavour and longer life than single-mesh alternatives. The 0.8-ohm orange base is where most vapers start.

The 0.6-ohm black base opens it up for cloudier draws. The 1.2-ohm green base tightens it down for firm MTL. Three pods per pack, all compatible across every NeXlim device. Grab yours from Pirate Vapes and browse our Replacement Pods collection.

FAQs

Which resistance should I start with? 

0.8 ohm (orange base). It is the bestseller and the most versatile. Works for both MTL with nic salts and lighter RDTL with 50/50. If you want more cloud, step down to the 0.6. If you want a tighter pull, step up to the 1.2.

Do these fit Xlim devices? 

No. NeXlim pods only fit NeXlim devices (NeXlim, NeXlim Go, NeXlim 2, NeXlim 2 Mini). They do not fit any Xlim kit. The pod shapes look similar but the contacts and dimensions are different.

How long does each pod last? 

2-3 weeks for most daily vapers. That translates to roughly 15-20 refills per pod. Sweet liquids shorten the lifespan. Tobacco and menthol profiles stretch further.

What do the base colours mean? 

Black = 0.6Ω (RDTL).Orange = 0.8Ω (MTL/RDTL). Green = 1.2Ω (MTL). The colour is visible at the bottom of the pod so you can identify resistance without reading labels.

How many come in a pack? 

Three. All three pods are the same resistance. Choose your resistance when you order. 

Do these pods leak? 

The five-layer sealed construction handles most of it. Do not overfill past the 2ml line, and make sure the rubber stopper is pressed firmly shut after filling. The bottom-mounted coil design keeps liquid above the contacts rather than pooling around them.