Aspire Favostix Replacement Pods

Aspire Favostix Replacement Pods

Two resistances in one pack, and the coil sits built into each pod rather than screwing in on its own. The Aspire Favostix Replacement Pods are the spare 2ml pods for the Favostix pen kit, sold three to a pack in either 0.6ohm or 1.0ohm.

Every pod carries a Kanthal AF mesh coil. When the flavour drops off, you take the whole pod out and drop in a fresh one. Fill from the base, match the resistance to the draw you prefer, and keep the kit you already own running. Genuine Replacement Pods, no coil-building, no guesswork.

Why vapers choose these:

• The coil is part of the pod, so there is nothing to prime separately, nothing to screw in wrong, and nothing to seat crooked. You replace one thing, not two.

• Mesh over round wire pulls sharper flavour from the same e-liquid.

• Two resistances in the range let you run a tight cigarette-style pull on the 1.0ohm or open it out for a warmer, airier hit on the 0.6ohm, all on the kit you already have.

• PCTG body, so you can see the fill.

• Three per pack keeps a spare or two in the drawer, which matters because a burnt pod always seems to go at the worst moment.

Favostix Replacement Pods Features

The Coil Lives Inside the Pod

Aspire built the heating element straight into the pod body, so it cannot be pulled out on its own. Practically speaking, that removes the fiddliest part of pod vaping. No dry-firing a fresh coil by mistake, no cross-threading. When performance fades, the whole unit gets replaced and you are back to a clean draw.

Why Mesh Instead of Round Wire?

The Kanthal AF mesh spreads heat across a wider strip of metal rather than a single coiled wire. Flavour lands cleaner, the ramp-up feels quicker, and the pod tends to hold its taste for longer before it starts to dull. Fair enough, mesh sounds like marketing until you compare it back to back.

A Wick Built for Refills

The wick pairs linen fibres with organic cotton. Linen handles heat well, and that combination is what lets each pod take several refills before the flavour tails off. Good with freebase or Nic Salts, whichever you run.

Fill It From the Base

Pull the silicone stopper on the underside, top up through the port, push the stopper back in. That is the whole job. The seal sits flush and stays put, so filling is tidy, and the pod is not prone to weeping once it is closed properly.

Keep an Eye on the Level

The pod body is translucent PCTG, not opaque plastic. You can glance at how much juice is left without popping the pod off the device, which is a small thing that saves you running one dry and scorching the wick.

Favostix Replacement Pods Resistance Options

Two options in the pack range, and the choice comes down to how tight you want the draw and how much vapour you are after.

Most popular is the 0.6ohm. It runs an airier, restricted direct-to-lung style at 15-18W, gives you a bit more warmth and cloud, and suits thicker juice. This is the one to reach for if you like Higher-VG E-Liquids, up to around 70 to 80% VG. Mid-strength salts sit well here too.

The 1.0ohm is the tighter, cooler mouth-to-lung pod, rated 12-15W. It leans towards a cigarette-style pull and works best with 50/50 or higher-PG juice. If you came off a disposable and want that familiar tight draw, start here. Pair it with our 50/50 E-Liquids or salts, and it is a sensible daily setup.

#buttons

• 0.6ohm
• 1.0ohm

How to Set Up the Favostix Pods

Under two minutes, no tools.

1. Take a fresh pod from the pack and pull the silicone stopper out of the base.

2. Drip three or four drops of e-liquid straight onto the exposed cotton through the port to wet the wick before you fill.

3. Fill through the same port to just below the top, then press the stopper firmly back in until it sits flush.

4. Clip the pod onto the device. The magnetic connection pulls it into place on its own.

5. Stand it upright and leave it for four to five minutes so the wick draws liquid all the way through.

6. Start on the lower end of the wattage range and nudge up until the hit feels right.

What's in the Favostix Pods Box

Three pods in the resistance you selected. That is it. No device, no charging cable, and no e-liquid, since these are spares for a kit you already own.

Made for the Aspire Favostix Family

These pods are keyed to the Aspire Favostix series. The magnetic fit and pod shape are fully cross-compatible across the original Favostix, the Favostix Mini, and the Favostix 2. The magnetic fit and pod shape are specific to that device, so they will not cross over to other Aspire pods. Not the Minican. Not anything in the Nautilus family. Not the Cloudflask line.

If your current pod says Favostix and slots on magnetically, you are in the right place. It is a tidy, single-purpose restock, which is why Pirate Vapes keeps both resistances together under Aspire's Pod Line.

About Aspire

Aspire has spent years on pod platforms where the coil and pod are one sealed unit, and the Favostix is a clear example of that thinking. Rather than sell you loose coils to seat and prime, the line puts a mesh element inside a translucent pod so the swap is a single, clean action.

It is a design aimed squarely at former disposable users and steady MTL vapers who want reliability over tinkering. That focus on simple, repeatable performance is a big part of why Aspire sits among the more trusted names on our Refillable Pod Kits shelf.

Stock Up and Save

Three pods, and most vapers get a good week or two out of each before the flavour dulls, so a single pack tends to cover the better part of a month. Grab a spare pack, and you are not caught short mid-week.

Every order from Pirate Vapes ships same day when it is placed before 4 pm, with Free Pirate Post over £40. All stock is TPD compliant, checkout is age-verified, and sales are strictly over-18s only.

Conclusion

If you run an Aspire Favostix and it still does the job, a fresh three-pack is the cheapest way to keep it going: pick 0.6ohm for an airier RDTL draw or 1.0ohm for a tight MTL pull, fill from the base, and you are set.

The built-in mesh coil keeps the swap simple and the flavour clean. Restock alongside your juice and Vape Accessories at Pirate Vapes.

FAQs

Which device do these Favostix pods fit?

These pods are fully cross-compatible across the entire Favostix family. They fit the original Aspire Favostix, the Favostix Mini, and the Favostix 2. The magnetic pod shape is specific to this series, so they will not fit other Aspire lines like the Minican, Nautilus, or Cloudflask pods.

What is the difference between Favostix pods 0.6ohm and the 1.0ohm?

The 0.6ohm gives an airier RDTL draw at 15-18W and takes thicker, higher-VG juice. The 1.0ohm is a tighter MTL pull at 12-15W, best with 50/50 or higher-PG.

Do I have to change a coil separately in Favostix pods?

No. The coil is sealed into the pod, so you replace the whole pod when it wears out.

Can I use nic salts in Favostix pods?

Yes, both resistances run salts or freebase. The 1.0ohm suits stronger salts for a tight throat hit, while the 0.6ohm pairs nicely with mid-strength salts or higher-VG freebase.

How long does each Favostix pod last?

Roughly a week to a fortnight with normal use, though sweeter, darker liquids gunk the wick faster and shorten that. Three pods per pack usually see you through the best part of a month.

I've seen a Favostix pod 3ml version listed. Why is this 2ml?

UK pods are capped at 2ml under TPD rules. The 3ml capacity you may spot elsewhere is the international spec and is not sold here.