Innokin Sceptre 2 Replacement Pods

Innokin Sceptre 2 Replacement Pods

A 2ml refillable pod that swaps coils instead of getting binned. This is the empty cartridge that keeps your Sceptre 2 running, built around Innokin's S Coil system with a push-to-fit base, so a fresh coil drops in without threading or fuss.

Side airflow lives on the pod itself, shifting you from a tight MTL draw to a looser RDTL one without pulling anything out. Fill through the silicone side port, clip it onto the magnetic connection, done. Sold as one pod with coils included, and it slots neatly into the world of Refillable Pod Kits.

Why vapers choose this:

• Coils swap, the pod stays. Because the S Coil presses in and out of the base, one pod carries you across dozens of coil changes before the shell itself ever needs replacing, which is where the real running-cost saving sits.

• Airflow on the pod, not the device. Slide it tighter for MTL or open it for a restricted lung hit, mid-session, without unclipping anything.

• Magnetic fitment. Line up the airflow slider with the recess, drop it on, and the magnets hold it firm.

• Two resistances, in the box. A 0.5ohm and a 0.6ohm coil land together, so you can find your preferred draw straight away.

• 2ml and fully TPD-compliant, side-filled behind a silicone plug that keeps liquid where it belongs.

Sceptre 2 Pod Features

The Coil Base Is the Whole Point

Older refill pods sealed the coil inside, so a worn coil meant a wasted pod. The Sceptre 2 pod flips that. The S Coil sits in a removable base held by O-rings, and when flavour fades you pull the old one and press a fresh one home. Cleaner, cheaper, and far less plastic in the bin over a year of daily use.

Fancy MTL Today, RDTL Tomorrow?

That is the airflow slider's job. Sitting opposite the fill port, it lets you close the draw down for a cigarette-style MTL pull or open it toward RDTL for a warmer, airier hit. The pod stays on the device the entire time. Small feature, genuinely useful when your mood shifts through the day.

Built to Take a Knock

The shell is a tough, dark-tinted plastic that stays discreet in the hand while still letting you read your liquid level at a glance. Paired with a good 50/50 or higher-PG e-liquid, it wicks cleanly and holds a seal well. Thin high-VG juice is not what this pod is for. Browse the 50/50 E-Liquids if you want a safe match.

Side Fill, Silicone Sealed

Lift the silicone plug on the side, tilt the nozzle in, fill to just under the max line, press the plug back. No unscrewing the top, no drips down the mouthpiece. Honestly, it is the quiet kind of design you only notice when a worse pod leaks in your pocket.

One Pod, Two Coils, Sorted

Each pack lands with the pod plus both S Coil resistances, so there is nothing else to buy on day one. Fit the resistance you fancy, keep the spare for when the first wears through. Practical, and it means you are not caught short mid-week.

Sceptre 2 Pod Resistance Options

The pod itself is one part. The draw comes down to which S Coil you press in, and both ship together in every pack.

Most vapers reach for the 0.6ohm first. It gives a tighter, cooler MTL draw that suits 10mg or 20mg nic salts and anyone chasing a cigarette-style pull. If you are stepping over from disposables, start here.

The 0.5ohm is the warmer of the pair. It opens the flavour up, pushes a bit more vapour, and sits happily in RDTL territory when you crack the airflow open. Good with 50/50 liquids and a strong pairing for Nic Salts at lower strengths.

#buttons

• 0.6ohm S Coil
• 0.5ohm S Coil

How to Set Up the Sceptre 2 Pod

Quick job. Two minutes, tops.

1. Pull the old coil out of the pod base if you are replacing one. It presses straight out.

2. Drop three to four drops of e-liquid directly onto the fresh coil's cotton ports before it goes anywhere.

3. Press the new coil firmly into the base until the O-rings seat and it sits flush.

4. Lift the silicone plug and fill with 50/50 or higher-PG liquid to just below the max line, then reseal.

5. Clip the pod on and let it stand for a full seven minutes so the wick draws liquid all the way through. Rushing this is how coils get scorched.

6. Start on the lower normal (blue LED) power mode, take a couple of soft pulls, then adjust airflow to taste.

What's in the Sceptre 2 Pod Box

One Sceptre 2 2ml pod and two Sceptre S Coils, typically a 0.5ohm and a 0.6ohm. That is it. No e-liquid, no device, no charger. This is a replacement cartridge for people who already run the kit, not a standalone starter setup.

Made Only for the Innokin Sceptre 2 Kit

These pods are cut specifically for the Innokin Sceptre 2 Pod Kit and lock on via its magnetic connection. They take the Innokin S (Sceptre) Coil family, which is the same coil platform the kit shipped with.

Some vapers also run them in the original Sceptre pod mod, though fitment can vary, so treat that as a bonus rather than a guarantee. What they will not fit is any other brand's pod, or Innokin's non-Sceptre systems, which each use their own hardware. If you want to explore the wider Innokin Range, the brand page has the matching kits and coils.

About Innokin

Innokin has spent years building a reputation as the MTL specialist that does not overcharge for it. The Sceptre line in particular is aimed squarely at ex-smokers and refill-focused vapers who want a dependable draw and cheap running costs rather than huge clouds.

The S Coil system that these pods use is a big part of that, keeping the pod reusable and the coil the only real consumable. It is unfussy, well-made hardware from a brand that UK vapers have trusted for a long time. You will find their full Vape Coils selection alongside the kits.

Stock Up and Save

Coils wear before pods do, but a spare pod in the drawer means a cracked shell never leaves you stuck. Grabbing a couple at once through our Plunder Packs keeps the per-pod price down and covers you for months.

Every order from Pirate Vapes ships same day when placed before 4 pm, packed properly so nothing rattles loose in transit. Age-verified checkout, over-18s only, and every pod is TPD-compliant.

Conclusion

The Sceptre 2 pod is a small, sensible bit of kit that does one job well: it keeps your Sceptre 2 running cheaply by making the coil the only part you regularly replace. Two resistances in the box, side airflow you can tweak on the fly, and a magnetic fit that just works.

If you already own the kit, this is the pod to keep on hand. Pick up more coils and Vape Accessories or head back to Pirate Vapes for the full Innokin lineup.

FAQs

Which device does the Sceptre 2 pod fit?

The Innokin Sceptre 2 Pod Kit. It attaches by magnets and takes the S Coil range. It is not designed for other brands' devices.

What coils come with the Sceptre 2 pods?

Two. A 0.5ohm and a 0.6ohm S Coil, one for a warmer draw and one for a cooler, tighter MTL hit.

Can I refill the Sceptre 2 pods, or is it single-use?

Refill it. That is the whole idea. Fill through the side port, swap the coil when flavour drops, and reuse the pod until the shell cracks or stops sealing.

What e-liquid should I use?

50/50 or higher-PG blends, including nic salts at 10mg or 20mg. Thick high-VG juice will not wick properly through these coils.

How long does the Sceptre 2 pod coil last?

Usually one to two weeks with daily use. Sweeter liquids gunk the mesh faster, so a heavy dessert vape will shorten that.

Does the Sceptre 2 pod hold more than 2ml?

UK pods are capped at 2ml under TPD rules. Some non-UK versions of this cartridge are listed at 3ml, but the pod sold here is the 2ml compliant version.