OXVA Origin X Replacement XL Pods

Empty pod cartridge for one of OXVA's most versatile pod mods. The Origin X XL pod holds 2ml under UK TPD rules, connects magnetically to the Origin X device, and accepts any coil from OXVA's Unicoil Range via press-fit installation. 

That means 0.2ohm mesh for sub-ohm DTL, 0.3ohm and 0.5ohm mesh for lighter DTL pulls, 1.0ohm KA1 for proper MTL vaping, or the Uni-RBA deck if you build your own. Bottom-fill port with a raised silicone plug. Pack of two. No coils included. Over 18s only.

Why vapers choose the Origin X pods:

• One pod accepts five different Unicoils spanning 10W to 60W, so your vaping style changes by swapping the coil, not the hardware

• Magnetic connection clicks the pod into the Origin X body with zero wobble and pulls free with a gentle press on both sides

• Bottom-fill silicone plug seals properly and resists the slow leaking that gravity-fed top-fill ports are known for

• Press-fit coil installation means you push the Unicoil into the base of the pod until it seats. No threading, no guessing.

• 2ml UK TPD capacity keeps the device compliant while the compact pod dimensions keep the overall kit pocketable

OXVA Origin X Replacement XL Pods Features

The Pod That Runs OXVA's Entire Unicoil Ecosystem

Five coils, one pod. The 0.2ohm mesh fires at 55 to 60W for dense sub-ohm clouds. The 0.3ohm mesh sits at 30 to 40W for a warmer DTL draw with strong flavour. The 0.5ohm mesh handles 20 to 25W for a lighter, more relaxed DTL or a loose MTL. 

The 1.0ohm KA1 runs at 10 to 15W for a tight, cigarette-style mouth-to-lung hit. And the Uni-RBA deck opens up full DIY coil building. All press-fit into the same pod shell. That versatility from a single cartridge is not common in pod mod territory.

Bottom Fill Beats Top Fill Here

The raised silicone plug on the base of the pod flips open to reveal the fill port. Turn the pod upside down, fill, close the plug, flip it back. Liquid sits above the coil and gravity feeds it down through the wicking ports. 

OXVA went with this approach specifically to reduce leaking around the coil contacts, and it works. The seal on the silicone plug is firm enough to stay closed during normal use but soft enough that you are not fighting it every refill.

Magnetic Connection With a Press-Release Mechanism

The pod drops into the Origin X and locks via magnets. Strong enough that the pod does not shift or rattle, even in a pocket. To remove it, press the sides of the pod and pull upward. 

That two-step removal prevents accidental disconnection, which matters when the device runs off an 18650 battery and delivers up to 60W of power. A loose pod at those wattages is a problem. This mechanism prevents it.

Sized for a Pod Mod, Not a Full Tank

At 34.5 x 28.9 x 25mm, the Origin X pod is compact relative to what the device can do. The Origin X itself is a proper pod mod running an 18650 cell with adjustable wattage, a Photon chip, and three operating modes (pod, RBA, and 510 adapter). 

The pod fits neatly into that body without adding bulk. If you have used Refillable Pod Kits before, this feels familiar in the hand but punches well above its size class.

Leak-Resistant by Design

OXVA's Unicoil system was engineered around leak prevention. The coil seats into the pod base with a firm press-fit, the fill port seals at the bottom away from the airflow path, and the magnetic connection keeps the pod flush against the device. 

Three points of potential leakage, all addressed. That matters more with sub-ohm coils at 55 to 60W where liquid gets thinner from heat and finds any gap it can.

How to Set Up the OXVA Origin X Replacement XL Pods

New pod, new coil, under three minutes.

1. Take a fresh Unicoil from the pack. Drop two to three drops of e-liquid directly onto the cotton visible through the coil's wicking slots. Rotate it and cover each port.

2. Push the coil into the base of the pod until it clicks into place. The press-fit is firm. You will feel it seat.

3. Flip the pod upside down. Open the raised silicone fill plug at the bottom. Fill with your chosen e-liquid to just below the max line. Close the plug and press it flat.

4. Turn the pod right way up and drop it into the Origin X device. The magnets will pull it into alignment.

5. Leave it sitting for five minutes without firing. The Unicoil uses a dense cotton wick that needs time to fully absorb liquid from the reservoir above. Firing before saturation burns the cotton permanently.

6. Start at the lower end of your coil's recommended wattage and increase gradually. The Photon chip handles the rest.

What's in the OXVA Origin X Replacement XL Pods Box

Two empty Origin X XL pod cartridges. No coils, no e-liquid, no device. Coils are sold separately in packs of five from the OXVA Range. If you are replacing a worn pod, you will likely need a fresh coil to go with it.

Built for the OXVA Origin X Pod Mod

These pods fit the OXVA Origin X only. The magnetic connection, pod depth, and coil seating are specific to the Origin X body. They do not fit the OXVA Xlim range, the OXVA NeXlim, or any other OXVA pod system. Different pod platforms entirely.

Some retailers list compatibility with the original OXVA Origin and the OXVA X. The Unicoil itself is cross-compatible across those devices, but the pod shell dimensions may differ. If you own an Origin or OXVA X rather than the Origin X, confirm the pod dimensions match your device before ordering. Browse more OXVA Pods for other models.

About OXVA

OXVA is a Shenzhen-based manufacturer that built its reputation on the Xlim series and the Unicoil platform. The Unicoil concept is simple: one coil format across multiple devices, covering MTL through to sub-ohm DTL and even rebuildable decks. 

The Origin X represents the higher end of OXVA's lineup, pairing the Unicoil system with 18650 battery power, adjustable wattage via the Photon chipset, and a 510 adapter for traditional tanks. It is a pod mod that genuinely bridges the gap between pod simplicity and mod-level control.

Stock Up and Save

Two pods per pack. Each pod lasts as long as the seal stays tight and the contacts stay clean, which is typically a few weeks to a couple of months with regular use. 

The coil inside wears out long before the pod does, so what you are really buying is insurance against accidental damage, discolouration, or a cracked housing. Grabbing a spare pack means you always have a fresh pod ready when you need one. 

Pirate Vapes ships every order the same day before 4 pm in padded packaging. Age-verified checkout, over-18s only, TPD compliant. Spend over £40, and it ships free with Free Pirate Post.

Conclusion

The Origin X XL pod is a straightforward replacement cartridge for one of OXVA's most capable devices. 2ml capacity, bottom fill, magnetic connection, and compatibility with the full Unicoil range from 0.2ohm sub-ohm to 1.0ohm MTL. Press-fit coil installation, leak-resistant design, and a pod shell built to last longer than the coils it houses. 

If your current pod is worn, cloudy, or cracked, a fresh two-pack gets you back to full performance. Browse more Vape Accessories and everything else at Pirate Vapes.

FAQs

Do the Origin X pods come with coils?

No. Empty pods only. Unicoils are sold separately in packs of five. You will need at least one coil to use the pod.

Which Unicoils fit the Origin X pod?

All five: the 0.2ohm mesh (55-60W), 0.3ohm mesh (30-40W), 0.5ohm mesh (20-25W), 1.0ohm KA1 (10-15W), and the Uni-RBA deck. The 0.2ohm is exclusive to the Origin X and does not work in older OXVA devices.

Will these pods fit the OXVA Xlim?

No. Completely different pod format. The Origin X pods only fit the Origin X device. The Xlim series uses its own pod cartridges.

How do I refill the Origin X pod?

Flip the pod upside down. Open the raised silicone plug at the bottom. Fill through the port, close the plug firmly, and flip it back. Do not overfill past the max line.

How long does the OXVA Origin X pod itself last?

The pod shell typically outlasts several coils. Replace it when the plastic becomes cloudy, the silicone plug loses its seal, or the magnetic contacts no longer sit flush.

What e-liquid ratio works best with the OXVA Origin X?

Depends on the coil. The 0.2ohm and 0.3ohm mesh coils suit 60/40 to 70/30 VG/PG. The 0.5ohm handles 50/50 to 60/40. The 1.0ohm KA1 works best with 50/50 or higher-PG blends and nic salts at 10 to 20mg.