OXVA Unicoil Replacement Coils

Oxva Unicoil Replacement Coils

Four resistances in one coil family, running from a tight 1.0ohm MTL coil up to a 0.2ohm sub-ohm cloud maker. The OXVA Unicoil replacement coils are the drop-in heads for the Origin series, sold five to a pack, with mesh builds for DTL vaping and a Kanthal coil for MTL.

Whatever draw you run on your Origin, there is a Unicoil to match. They push straight into the pod base, no screwing and no fuss, and they suit the whole OXVA Range of Origin devices.

Why vapers choose this:

• One platform covers every style. From a cigarette-tight 1.0ohm draw-through to full sub-ohm clouds, the same coil family handles MTL, restricted DTL, and DTL without you switching hardware.

• Mesh where it counts. The 0.2, 0.3, and 0.5 mesh heads heat fast and taste clean.

• Push-to-fit, done in seconds. No threads, just press the coil into the pod.

• Organic cotton wicking. Keeps flavour honest and dry hits rare.

• Five to a pack. A proper run before you need to reorder.

OXVA Unicoil Features

Mesh Builds That Pull Real Flavour

Mesh heats across a wide, even surface, so the liquid vaporises quickly and the flavour lands sharp rather than dull. On the 0.3ohm at 30-40W, the clouds are generous, and the taste is rich, which is exactly what you want from a higher-VG juice. Load it with a 70-30 Shortfill and let it breathe.

Why Four Resistances?

Because one coil cannot do everything well. A DTL cloud coil makes a poor MTL salt vape, and the other way round. Giving you four heads on a single platform means you tune the whole feel of the device, tight and cool or loose and warm, just by changing the coil. Sensible design, honestly.

The Kanthal Coil Earns Its Place

The 1.0ohm Kanthal A1 is the quiet workhorse here. At 10-15W it delivers a restrained, cigarette-like MTL draw with a firm throat hit, which makes it the natural pick for anyone running stronger salts or stepping off cigarettes. It is the least flashy coil in the range and probably the most used.

Push It In and Go

No coil tool, no fiddly threads. You pull the old head, press the new one into the pod base until it seats, and you are ready to fill. That plug-and-play fit is a small mercy when you are changing a coil on the move, and it keeps the whole process under a minute.

Built to Resist Leaks

OXVA designed the Unicoil with an anti-leak, anti-spitback structure, so you get fewer wet pockets and less liquid creeping up the airflow. Pair that with organic cotton, and the coils tend to hold their flavour longer than a lot of budget heads, which stretches the pack further.

OXVA Unicoil Resistance Options

Four heads, three vaping styles. The right one comes down to your draw, your device, and the liquid you run, so match the coil to those rather than just grabbing the lowest resistance.

The 0.3ohm mesh is the crowd favourite for most Origin owners. At 30-40W it strikes the balance between big flavour and manageable clouds, and it happily runs high-VG freebase liquid all day. If you are unsure where to start with DTL, start here.

Step up the restriction with the 0.5ohm mesh at 20-25W. A tighter, restricted-DTL draw with warmer vapour, good for lower wattages and slightly higher-strength liquids. The 0.2ohm mesh sits at the other extreme: a proper 55-60W sub-ohm cloud coil, and one to run on the Origin X only. Finally, the 1.0ohm Kanthal at 10-15W is your MTL coil, built for tight draws and Nic Salts.

#buttons

• 0.2 Ohm
• 0.3 Ohm
• 0.5 Ohm
• 1.0 Ohm

How to Set Up the OXVA Unicoil

Two minutes, and the wait is the important bit.

1. Empty the pod and pull the old coil out of the base.

2. Drip three or four drops straight onto the exposed cotton ports of the new coil until it looks glossy and saturated.

3. Push the new coil into the pod base until it clicks home.

4. Fill the pod to match the coil: high-VG liquid for the mesh heads, a 50/50 or salt for the 1.0ohm.

5. Leave it a good ten minutes after filling so the cotton fully soaks before the first pull. This is the single best way to avoid a burnt coil.

6. If using the 0.3ohm, 0.5ohm, or 1.0ohm, screw your existing Unicoil Airflow Ring onto the base of the new coil. (The 0.2ohm does not use an airflow ring).

7. Start near the bottom of the coil's wattage band and climb until the draw tastes right.

What's in the OXVA Unicoil Box

Five OXVA Unicoil replacement coils in your chosen resistance, each with the organic cotton pre-fitted. That is everything. No pod, no device, and no e-liquid.

These are replacement heads for an OXVA Origin-series kit you already own, so make sure your device is one of the compatible models before ordering.

Made for the OXVA Origin Series

The Unicoil is the coil platform behind OXVA's Origin range, so these heads drop into the Origin X, Origin 2, Origin Mini, Origin SE, and the Velocity LE kit. They press into the same Origin pods, and the only real caveat is the 0.2ohm, which is wider, does not use an airflow ring, and is built exclusively for the Origin X pod. Need spare cartridges too? The OXVA pods range has them. Every OXVA coil sold through Pirate Vapes is a genuine part.

They are not the coils for the OXVA Xlim series, which uses whole integrated-coil pods rather than separate heads, and they will not fit non-OXVA devices. If your kit is an Origin, you are covered. If it is anything else, check the model first.

About OXVA

OXVA built its name on the Origin pod mod, and the Unicoil is the system that made that range so adaptable. Rather than tie each device to a single coil, OXVA created one modular head family spanning tight MTL right through to sub-ohm DTL, so a single Origin kit could cover several vaping styles.

That flexibility, along with a reputation for strong flavour and leak-resistant builds, is why the Origin series stayed popular for years. The Unicoil remains the coil of choice for anyone running an older Origin device.

Stock Up and Save

Coils are a running cost, not a one-off, so buying a couple of packs ahead means you are never left with a burnt head and no spare. Pirate Vapes ships every order the same day when it lands before 4 pm, boxed to arrive undamaged.

Age-verified checkout, over 18s only, and these coils are part of a TPD-compliant Origin ecosystem. A multi-pack keeps your per-coil price sensible.

Conclusion

The OXVA Unicoil replacement coils are the simplest way to keep an Origin-series kit performing, with four resistances covering everything from tight MTL salts to full DTL clouds in one plug-and-play family.

Match the coil to your device and draw, prime it properly, and each one will serve you well. Round out your setup with a few Vape Accessories, and shop the coils and the rest at Pirate Vapes.

FAQs

Which devices do Unicoil Replacement Coils fit?

The OXVA Origin series: Origin X, Origin 2, Origin Mini, Origin SE, and the Velocity LE. They press into the standard Origin pods.

How many Unicoil Replacement Coils come in a pack?

Five, all the same resistance you select.

Which resistance should I pick for Unicoil Replacement Coils?

0.3ohm for everyday DTL flavour, 0.5ohm for a tighter restricted draw, 0.2ohm for clouds on the Origin X, and the 1.0ohm Kanthal for tight MTL with salts.

Will Unicoil Replacement Coils work on my Xlim?

No. The Xlim uses whole pods with built-in coils, so these separate Unicoil heads are for the Origin range only.

How long does a Unicoil coil last?

Usually anywhere from a few days to a couple of weeks, depending on the wattage, your liquid, and how much you vape. Sweeter, darker liquids gunk a coil up faster.

What e-liquid suits Unicoil Replacement Coils?

High-VG freebase for the mesh DTL coils, and a 50/50 or nic salt for the 1.0ohm MTL coil.