OXVA Unipro Replacement Coils

Oxva Unipro Replacement Coils

Big, airy direct-lung clouds from the OXVA Velocity start with a fresh coil. The OXVA Unipro replacement coils are the press-fit mesh heads built for the Velocity pod kit, sold five to a pack. Two resistances cover the range: the 0.15ohm runs full DTL at 60 to 80W, while the 0.3ohm pulls tighter at 30 to 40W.

Both use a mesh heating element, both fire up quickly, and both are made to resist leaks and spitback. Feed them high-VG juice and a mod that can push the wattage. Simple, reliable Vape Coils for keeping a Velocity tasting right.

Why vapers choose this:

• Mesh heats evenly across a wide surface, which is where the flavour comes from. OXVA reworked these over the older coils for cleaner taste and denser vapour, and the break-in time is short, so you get very little of that fresh-cotton dullness on the first few pulls.

• Two resistances, two moods. The 0.15ohm for clouds, the 0.3ohm for a tighter, cooler draw.

• Press-fit fitting means no threads to cross and no coil seized in place after a hot session.

• Built to stay dry on the outside. The design pushes back against leaks and spitback, which the Velocity range needed.

• Five in a box, which is the honest amount to buy for sub-ohm vaping since higher wattage and sweeter High-VG E-Liquid chew through coils faster than lighter setups do.

OXVA Unipro Replacement Coils Features

Mesh Is Doing the Real Work

Each head runs a mesh heating element rather than old-style wire. Mesh spreads the heat over a bigger area, so the coil warms faster and more evenly, and the flavour lands crisp rather than muted. It also wicks well at higher wattage, which keeps dry hits at bay when you are pushing the 0.15ohm near 80W.

Which One Suits Your Draw?

Honest answer: it depends on how you like to vape. The 0.15ohm at 60 to 80W is the cloud coil, warm and open and loud. The 0.3ohm at 30 to 40W pulls tighter and cooler, closer to a restricted direct-lung style. Pick the draw first, then the wattage follows.

Press It In, You're Done

Almost no threading here. Once you screw your existing airflow ring onto the base, the whole unit push-fits into the pod. The coil push-fits into the base of the Velocity pod, held by the seating rather than a screw thread. That means quick swaps, no cross-threaded heads, and nothing stuck fast when it is hot. Pull the old one, seat the new one, refill. Two minutes at most.

Feed It the Right Juice

At these resistances, thin high-PG liquid and strong nicotine will taste harsh and wick poorly. Reach for high-VG instead, ideally 70/30 Shortfills or thicker, kept at low nicotine. It clouds better, it wicks better, and it keeps the throat hit civil.

Made to Stay Clean

Leaks and spitback are the usual sub-ohm annoyances, and OXVA built these to fight both. Fewer drips in your pocket, fewer hot flecks on your lip. Not glamorous, but the sort of thing you notice every day once it stops happening.

OXVA Unipro Replacement Coils Resistance Options

Two heads in the range, and the choice is really about how open you want the draw. Both sit well under 1 ohm, so you will need a capable Regulated Mod behind them.

Most popular: the 0.15ohm. This is the coil most Velocity owners reach for, rated 60 to 80W for full direct-lung vaping. It gives the biggest clouds and the most flavour of the two, and it is the natural match for the Velocity's higher power output. If you bought the kit for clouds, start here.

For a tighter draw: the 0.3ohm. Rated 30 to 40W, it runs cooler and pulls a little more restricted, which suits vapers who want a restricted direct-lung style or a bit more coil life between changes. It sips less juice and less battery too. A sensible second coil to keep in the drawer.

#buttons

• 0.15 Ohm
• 0.30 Ohm

How to Fit the OXVA Unipro Replacement Coils

Quick, threadless, done in a couple of minutes.

1. Empty the Velocity pod first, then pull the spent coil straight out of its seating. It releases with a firm tug, no twisting.

2. Drip a few drops of high-VG e-liquid into the coil's wicking ports and one down the centre so the cotton starts saturated.

3. Press the fresh coil firmly into the base until it clicks home and sits flush.

4. Refit the pod and fill with your high-VG liquid, letting it settle around the new head.

5. Let it sit until the cotton looks fully darkened, roughly seven minutes, so nothing fires dry.

6. Start near the bottom of the coil's range and build the wattage up until the flavour peaks.

What's in the OXVA Unipro Replacement Coils Box

Five coils in your chosen resistance, either the 0.15ohm or the 0.3ohm, individually sealed. That is the lot. No pod, no kit, no e-liquid, so you will need your own Velocity and a bottle of high-VG juice ready to go.

Made for the OXVA Velocity

These coils were designed around one kit: the OXVA Velocity and its 21700 variants. They press straight into the Velocity pod with no adapter needed, so a five-pack keeps the kit you already own running. Browse compatible OXVA pods if you need a fresh pod to go with them.

What they do not fit is the rest of OXVA's line. Not the Origin series. Not the Xlim pods. Those run OXVA's other coil platforms, which are a different size and fitting entirely. If your coil says Unipro and your kit says Velocity, you are in the right place.

About OXVA

OXVA went from a newcomer to a fixture on UK shelves in a short space of time, largely on the strength of kits like the Xlim and the Velocity. The Velocity leaned into serious direct-lung power, and the Unipro coils were its dedicated heads, with an RBA section offered alongside for anyone who wanted to build their own.

That mix of ready-made mesh coils and a rebuildable option is very OXVA: give people the easy route and the tinkerer's route in the same platform. Explore the wider OXVA Range for the kits these coils were made to serve.

Stock Up and Save

Half the fun of the Velocity is dialling it in, and that is easier with both resistances on hand. Keep a pack of the 0.15ohm for cloud days and a pack of the 0.3ohm for when you want something tighter, and you can switch to suit the juice in front of you. Sub-ohm heads wear faster than most, so five per pack rarely feels excessive.

Every order from Pirate Vapes ships same day when placed before 4 pm, in discreet packaging. All stock is TPD compliant; checkout is age-verified, strictly over-18s only.

Conclusion

If you run an OXVA Velocity, the Unipro coils are the simple way to keep the flavour and clouds where they should be. The 0.15ohm is the cloud coil for 60 to 80W, the 0.3ohm is the tighter option for 30 to 40W, and both press in without a thread in sight.

Just pair them with high-VG juice and a mod that can supply the power. Browse more Vape Accessories and the full lineup at Pirate Vapes.

FAQs

Which kit do the Unipro coils fit?

The OXVA Velocity and its 21700 versions. They will not fit the Origin series or the Xlim pods, which use different OXVA coils.

What's the difference between the two Unipro coil resistances?

Power and draw. The 0.15ohm runs 60 to 80W for full DTL clouds. The 0.3ohm runs 30 to 40W for a cooler, more restricted pull.

Do I need a powerful mod for the Unipro coils?

Yes. Both are sub-ohm, so they need a regulated mod that can safely fire below 1 ohm. The 0.15ohm in particular wants a device comfortable up around 80W.

What e-liquid should I use for the Unipro coils?

High-VG, 70/30 or thicker, at low nicotine. Thin high-PG juice and strong nic salts do not suit sub-ohm coils and taste harsh.

How many Unipro coils are in a pack?

Five. The RBA section, if you want to build your own, is a separate purchase.

How long does each Unipro coil last?

Depends on wattage and juice. Higher power and dark, sweet liquids shorten coil life. Many sub-ohm vapers get roughly a week per coil, which is why a five-pack makes sense.