SMOK RPM 2 Replacement Coils

Built for SMOK's RPM 2 pod platform, these press-fit coils come five to a pack and cover MTL, RDL and DTL without needing a second device. The mesh options spread heat across a wider surface so flavour comes through cleaner and cloud fills out properly, while the dual-core DC builds sit at lower wattage for a tighter, throat-focused pull that works well with nic salts. 

Fitting one is dead simple: push it into the pod base, prime the cotton, and you are vaping. No threading, no fiddly alignment, nothing to overthink. The same coil platform runs across more than ten SMOK Kits too, so whether you are on a Nord 4, an RPM 85 or an IPX 80, one pack has you sorted. Pirate Vapes ships every order with full tracking and age-verified UK delivery.

Why vapers choose this:

• 5 resistance options spanning MTL through DTL from a single coil platform, so one purchase covers whichever draw style you prefer on a given day.

• Mesh builds at 0.16Ω, 0.23Ω and 0.3Ω that spread heat evenly for fuller flavour and longer coil life than standard round wire.

• Press-fit installation that clicks into place in seconds, with no risk of cross-threading or overtightening.

• Cross-compatibility with the Nord 4, IPX 80, RPM 85, RPM 100 and more than ten other SMOK kits on the same platform.

• Organic cotton wicking that keeps flavour honest from the first puff right through to the end of the coil's life.

SMOK RPM 2 Replacement Coils Features

Mesh Heating for Richer Flavour

The 0.16Ω, 0.23Ω and 0.3Ω coils use a flat mesh strip instead of wrapped wire. That wider heating surface contacts more e-liquid at once, so the cotton vapourises evenly rather than in hot spots. In practice, it means cleaner taste, thicker cloud, and a coil that holds its flavour for longer before the cotton degrades.

Dual-Core Wire for a Tighter Draw

The 0.25Ω and 0.6Ω coils run dual-core wire, which is two parallel strands that heat together at lower wattage. The 0.6Ω variant sits comfortably at 12–25W and pairs naturally with nic salts, giving a controlled throat hit without heavy vapour. If you are moving away from disposables, this is the coil that will feel most familiar.

Press-Fit Coil Swap

Every RPM 2 coil uses the same push-in connection. Line it up with the pod base, press until it seats, and the rubber O-ring around the housing seals it airtight to guard against leaks. Pulling the old coil out is just as simple. The whole swap takes under a minute with clean hands and no spare parts.

Wattage Range Across Five Builds

The lineup spans roughly 12W to 50W depending on the coil you fit. That means you can run a cool, quiet MTL at 15W on the 0.6Ω coil one day, then switch to a warmer DTL pull at 40W on the 0.16Ω mesh the next, all on the same device and pod.

One Coil Range, Many Devices

SMOK designed the RPM 2 platform to work across a broad spread of hardware. Whether you own the compact IPX 80 or the higher-powered RPM 100, the same five-pack of coils fits. That cuts down on the number of coil types you need to keep track of and means no wasted stock if you upgrade.

SMOK RPM 2 Replacement Coils Resistance Options

There are no flavours to choose here. These are hardware coils, and the flavour comes from whatever e-liquid you fill the pod with. What you are selecting is the resistance, which determines your draw style, your wattage range and the type of e-liquid that works best. 

0.16Ω Mesh Coil: the go-to for DTL vapers who want bold flavour and thick cloud at 25–50W. Pair it with a high-VG e-liquid, 70% VG or above, and run the airflow wide open.

 0.25Ω DC Coil: a dual-core build rated at 30–50W that balances vapour and flavour for a restricted DTL or warm RDL draw. Works well with 70/30 blends. 

0.6Ω DC MTL Coil: built for mouth-to-lung at 12–25W, smooth and restrained. Nic salts or 50/50 freebase suit this coil best, and the lower power means less e-liquid consumption.

0.3Ω Mesh Coil: a mesh option for RDL vaping at moderate wattage. Good for vapers who want mesh flavour without a wide-open DTL pull. 

0.23Ω Mesh Coil: a sub-ohm mesh coil suited to DTL or warmer RDL draws. Pair with high-VG e-liquid for best results. Browse the e-liquid range and match the juice to whichever coil you fit.

How to Set Up the SMOK RPM 2 Replacement Coils

1. Remove the old coil. Grip the base of the spent coil and pull it straight out of the pod. Set aside for disposal.

2. Prime the new coil. Take a fresh coil from the pack and drip three to four drops of e-liquid directly onto the exposed cotton through the side wicking ports. This saturates the cotton before it ever touches heat.

3. Install the coil. Line the new coil up with the pod base and press it firmly until it clicks into place and sits flush. The rubber O-ring will seal it airtight.

4. Fill the pod. Add e-liquid through the side fill port, keeping it below the max line. Stand the pod upright and leave it for five to ten minutes so the cotton soaks through completely.

5. Start low and adjust. Set your device to the bottom of the coil's rated wattage range and take a few short pulls. Gradually increase the wattage until you find the sweet spot. Skipping the prime is the fastest way to scorch the wicking and ruin a brand-new coil, so the five-minute wait is always worth it.

What's in the SMOK RPM 2 Replacement Coils Box

• Five RPM 2 coils of the same resistance, each individually wrapped.

• All five coils match the variant you selected at checkout; this is a single-resistance pack.

• No pod, device, e-liquid or additional accessories are included.

• Make sure you have a compatible RPM 2 pod and a bottle of e-liquid to hand before swapping in a new coil.

Built for the Entire SMOK RPM 2 Coil Platform

SMOK RPM 2 coils work across a wide range of SMOK devices that use the RPM 2 pod platform.

Compatible kits include SMOK RPM 2, RPM 2S, RPM 85, RPM 100, RPM C, Nord 4, Nord X, Nord C, IPX 80, G-PRIV Pod, SCAR-P3, SCAR-P5, Thallo, and Thallo S when paired with their matching RPM 2 compatible pods.

These coils are not compatible with older RPM, RPM 4, RPM 5, or TPP pod platforms, as each uses a different coil fitment. Always check your pod type before ordering.

About SMOK

If you have walked into a vape shop anywhere in the UK, you have almost certainly seen SMOK on the shelf. They have been around for over a decade and they make everything from pocket-sized pod kits to chunky box mods that push serious wattage.

The RPM coil platform ties a big chunk of that lineup together, and the RPM 2 series is where SMOK refined it, adding more coil options and sorting out the airflow issues that the first-gen RPM coils sometimes had. Spares are everywhere, prices stay reasonable, and one coil range covers a genuinely long list of devices, which is exactly what most vapers actually care about.

Stock Up and Save

You will know the coil is done before you even think to check. The flavour goes flat, maybe a bit papery, and that is your cue. Having a spare pack already in the drawer saves you from limping along on a burnt coil while you wait for a delivery. 

Grab a multi-buy and the per-coil cost drops too. Every order from Pirate Vapes goes out carefully packed, fully tracked, and delivered only to verified over-18s at the door. 

Pirate Vapes source all hardware direct from authorised suppliers, so what arrives is genuine SMOK and fully TPD-compliant.

Conclusion

Five resistances, mesh and dual-core builds, MTL through to DTL, and all of it off one coil platform without needing a second device. 

The press-fit swap takes seconds, the organic cotton keeps flavour true to whatever juice you fill with, and because the same coil fits the Nord 4, the RPM 85, the IPX 80 and a stack of other SMOK kits, you are not hunting down a different coil every time you change hardware. Prime it, pair it with the right e-liquid, and let it do the work. 

Pirate Vapes has them in stock with tracked UK delivery. And if you need a device to go with them, the SMOK RPM 2 Kit or the SMOK Nord 4 in our SMOK Range are both worth a look.

FAQs

How often should I expect to replace an RPM 2 coil?

Most vapers get one to two weeks from a single coil with regular use. Sweet or heavily flavoured e-liquids tend to gunk the cotton faster, and consistently running at the top of the wattage range will shorten things too. When the flavour starts to taste flat or slightly burnt, it is time for a fresh coil.

Which resistance works best with nic salts?

The 0.6Ω DC MTL coil is the natural pairing. It runs at 12-25W with a tighter draw, which suits the higher nicotine concentration in salt-based e-liquids and delivers a smooth throat hit without excessive vapour.

I own a Nord 4. Will these coils fit?

They will, but only if you are using the Nord 4 RPM 2 pod. The Nord 4 also accepts a standard RPM pod, and these coils will not fit that one. Check which pod is currently in your device before ordering.

Can I swap between mesh and DC coils on the same pod?

Yes. All five RPM 2 coil types share the same press-fit connection, so you can pull out a mesh coil and push in a DC coil without changing the pod. Just prime the new coil and let it soak before firing.

What happens if I skip priming?

The cotton burns on the first few pulls, and the coil is effectively ruined. Drip e-liquid onto the wicking ports, install the coil, fill the pod, and wait five to ten minutes. It is the single biggest thing you can do to protect coil life.

Is there a difference between RPM and RPM 2 coils?

Yes. They are separate platforms with different physical sizes and connections. An RPM coil will not fit an RPM 2 pod, and vice versa. Make sure the coil and pod both carry the RPM 2 marking.

What wattage should I start at?

Always begin at the bottom of the rated range and adjust upward. For the 0.16Ω mesh that means starting around 25W, for the 0.6Ω DC around 12W. Working up gradually beds the cotton in and avoids a harsh first hit.

Do all five coils in the pack have the same resistance?

Yes. Each pack contains a single resistance type. If you want to try more than one option, you will need to order separate packs.