SMOK RPM80 RGC Replacement Coils

Four options on one listing, covering everything the RGC pod needs. The 0.17 Ohm Mesh is the cloud coil, running SMOK's conical nexMesh technology at 40 to 80W for warm, dense DTL hits. The 0.6 Ohm DC MTL drops to 8 to 16W for a tight, quiet draw on Nic Salts.

There is also a replacement RGC pod (5ml, 3-pack) and an RBA coil deck for builders who want to wrap their own wire. All plug 'n' play. Works across the RPM80 range and the Fetch Pro. Pirate Vapes ships them age-verified across the UK.

Why vapers choose this:

• Two coil styles covering 8W MTL right through to 80W DTL from one pod.

• Conical nexMesh on the 0.17Ω for faster, more even heating and bigger flavour.

• An RBA option for vapers who want to build their own coils instead of buying pre-made.

• A replacement pod option on the same listing, so you can grab everything in one order.

• Plug 'n' play installation across all options, no threading.

SMOK RPM80 RGC Replacement Coils Features

Conical nexMesh on the 0.17Ω

The 0.17Ω coil does not use a flat mesh strip. It uses a conical honeycomb mesh that tapers from wide at the base to narrow at the top, channelling airflow upward through the centre. That cone shape compresses the vapour stream for denser cloud and more concentrated flavour than a standard flat mesh at the same wattage. Best around 55 to 60W with the airflow partially closed.

0.6Ω DC MTL for Nic Salts

The DC coil runs two small wires and a 2mm inner bore for clean wicking. At just 8 to 16W, it produces modest, discreet vapour with a firm throat hit. Made for 50-50 juice and nic salts, and it barely touches the battery. If you bought the RPM80 for MTL, this is the coil.

The RBA Deck

For experienced vapers who prefer wrapping their own coil. The RGC RBA ships with a single coil build deck, a pre-installed 0.6Ω NiCr coil, a Phillips screwdriver and spare o-rings. It plugs into the RGC pod the same way the pre-made coils do. Not for beginners, but for builders it cuts the cost of consumables to almost nothing.

RGC Pod on the Same Listing

The third option on the picker is the RPM80 RGC Replacement Pod itself, a 5ml pod sold in a 3-pack. This is the housing the RGC coils sit inside. If your pod cracks, clouds up or starts leaking from the seal, you replace it here without buying a whole new kit.

Plug 'n' Play, No Threads

Every RGC coil and the RBA push into the pod base with a friction fit. No screwing, no alignment. One push in, one pull out. The pod then clicks onto the RPM80 device magnetically. Quick, clean, minimal fuss.

SMOK RPM80 RGC Replacement Coils Variant Options

This listing covers four different products. Pick the one you need.

• 0.6 Ohm DC MTL - dual coil, 8 to 16W, tight MTL draw, best on nic salts (5-pack)

• 0.17 Ohm Mesh - conical nexMesh, 40 to 80W, warm DTL clouds, suits High-VG Juice (5-pack)

• RPM80 RGC Replacement Pod (5ml) (3PCS) - the pod housing, no coil inside, 3-pack

• RPM80 RGC RBA Coil - rebuildable deck, pre-installed 0.6Ω NiCr, for experienced builders (1 piece)

Match the juice to the coil: the 0.6Ω wants thin nic salts or 50-50. The 0.17Ω wants thick high-VG at 70% or above.

How to Set Up the SMOK RPM80 RGC Replacement Coils

1. Pull the RGC pod off your RPM80 device.

2. Turn the pod upside down and pull the old coil or RBA straight out of the base.

3. Push the new coil firmly into the base until it stops. No turning needed.

4. Flip the pod back over, fill with e-liquid through the fill port, and let it stand for five minutes.

5. Click the pod back onto the device and vape. Set your wattage to match the coil you fitted.

What's in the SMOK RPM80 RGC Replacement Coils Box

Depends on the option you picked. The 0.17Ω Mesh and 0.6Ω DC MTL come as a 5-pack of coils. The RGC Replacement Pod comes as a 3-pack of empty pods. The RBA comes as a single deck with a screwdriver and O-rings. 

No device and no e-liquid with any of them. Grab a Shortfill for the 0.17Ω or nic salts for the 0.6Ω.

Works With the RPM80 Family and the Fetch Pro

The RGC coils and pod fit three SMOK Devices, all via the same RGC pod. They do not fit the RPM pod (which takes RPM coils instead), and they do not fit any other SMOK device. 

The RPM80 kit ships with both an RPM pod and an RGC pod, so make sure you are ordering for the RGC side. You will find the full range in our SMOK collection, with more coil options in the coils section.

About SMOK

The RPM80 was SMOK's answer to the pod-mod wave, and the RGC coil is the half that handles high-power DTL. The conical nexMesh design was a genuine step forward when it launched, compressing the vapour path for denser, more focused flavour than a standard flat mesh.

The inclusion of an RBA option on the same platform was a smart move too, giving advanced vapers a way to cut their coil costs to pennies. SMOK has since moved on to newer platforms, but the RPM80 and its RGC coils still hold up for anyone who values versatility.

Stock Up and Save

The 0.17Ω mesh burns hot and gets through juice. The 0.6Ω sips it quietly. Either way, a 5-pack covers a month or more, and ordering the pod alongside the coils in one go saves a second delivery.

Genuine SMOK, dispatched tracked, age-verified checkout. Over 18s only. Browse our multi-buy offers for bundle savings on juice.

Conclusion

Two coils, a pod and an RBA on one listing. The 0.17Ω conical nexMesh for serious DTL clouds, the 0.6Ω DC for quiet MTL on nic salts, the pod when yours needs replacing, and the RBA for builders. All plug 'n' play into the same RGC pod, and they work across the RPM80 range plus the Fetch Pro. Pick what you need and go. Grab yours from Pirate Vapes with fast, age-verified UK delivery.

FAQs

RGC coils or RPM coils, which do I need?

The RPM80 ships with two pods. The RGC pod takes RGC coils (these). The RPM pod takes RPM coils. They are different sizes and not interchangeable. Check which pod you are refilling.

What is the conical mesh on the 0.17Ω?

A honeycomb mesh shaped like a cone rather than a flat strip. The cone compresses the airflow upward through the centre, producing denser vapour and more concentrated flavour than flat mesh.

Is the RBA worth it?

If you are comfortable building coils, yes. It plugs into the RGC pod the same way a pre-made coil does, and it cuts your coil costs to almost nothing. If you have never built before, stick with the pre-made options.

What juice for the 0.17Ω?

High-VG at 70% or above, freebase at 3 to 6mg. It runs at 40 to 80W, so thin juice will flood and nic salt strengths will be far too strong.

What juice for the 0.6Ω?

Nic salts at 10 to 20mg or 50-50 e-liquid. It runs at just 8 to 16W, designed for a tight, discreet MTL draw.

Does the pod come with a coil inside?

No. The RPM80 RGC Replacement Pod option is the empty pod housing only. You buy and install the coil separately.