Eleaf GTL Vape Coils

Eleaf GTL Vape Coils

A pack of five mesh replacement coils for the Eleaf GTL system, available in three resistances: 0.4ohm, 0.8ohm and 1.2ohm. The Eleaf GTL coils run a Kanthal mesh build with organic cotton wicking, so they heat evenly and pull clean flavour whether you vape tight mouth-to-lung or open direct-to-lung.

Each coil is push-fit, meaning swaps take seconds with no screwing required. Pick the resistance that matches your device and draw, and keep a pack spare so a tired coil never stops your day. Browse the wider Vape Coils range at Pirate Vapes.

Why vapers choose these:

• Genuine Eleaf GTL coils, five to a pack, so the per-coil cost stays low and you always have a fresh one ready.

• Mesh build for even heating, quick ramp-up and clean, consistent flavour.

• Push-fit fitting that swaps in seconds without the need for threads or tools.

• Three resistances covering tight MTL right through to airy DTL.

Eleaf GTL Coils Features

Kanthal Mesh for Better Flavour

Every coil uses a Kanthal mesh heating element rather than old-style round wire. Mesh spreads heat across a wider surface, so it warms quickly and keeps flavour clean and steady from the first draw deep into the coil's life. Organic cotton around it wicks liquid fast enough to keep pace with the mesh.

Easy Push-Fit Coil Replacement

The GTL series is push-fit, so a coil presses straight into the pod or tank base with no threads to line up. Push it fully flat until it seats flush, or the O-rings will not seal properly. The whole physical change takes seconds, ensuring you spend less time fiddling with hardware.

(Note: Because the tank does not have a juice lock, ensure your pod is empty before pulling the old coil out to avoid a spill).

Eleaf GTL Coils Resistance Options

Match the resistance to your device's wattage and the draw you prefer. As a quick guide:

#buttons

• 0.4 ohm
• 0.8 ohm
• 1.2 ohm

If you are unsure, the 0.8ohm is the safe middle ground. Lower-resistance coils run hotter and tend to wear faster, while the 1.2ohm typically lasts the longest.

Eleaf GTL Vape Coils Compatible Devices

Never assume a coil fits. These Eleaf GTL coils are confirmed for the following Eleaf devices:

• GTL Pod Tank,

• GTL Pod,

• GTL Mini Pod,

• GTL D20 Tank,

• Pico Compaq,

• iStick T80 (GTL) kit,

• iStick Power 2,

• iStick Power 2C,

• iStick Power Mono,

• iStick i40,

• iStick Pico Plus GTL,

• iStick Amnis 2,

• iJust 3 (GTL),

• iJust AIO,

• iJust AIO Pro,

• iJust D20,

• iJust P40,

• iSolo R,

• iSolo Air,

• iSolo Air 2,

• iSolo Air 3,

• Glass Pen kit,

• FlasQ Pod,

• and the TECC Arc Impact kit.

They will not fit non-Eleaf devices, so check your exact model and variant before buying. Browse matching Vape Tanks, Refillable Pod Kits and Vape Mods at Pirate Vapes.

How to Fit the Eleaf GTL Coils

A quick job once you have done it.

1. Detach the pod or tank from your device base. Important: Empty any remaining liquid or ensure the tank is vaped dry. Pulling the coil out of a full tank will cause the liquid to pour out.

2. Pull the old coil straight out of the base. It releases without unscrewing.

3. Prime the new coil by dripping a few drops of e-liquid straight down the centre hole directly onto the internal mesh, and a drop onto each of the exposed outer cotton ports.

4. Push the new coil fully into the pod base, pressing until it sits perfectly flat and flush so the O-rings seal.

5. Reassemble and fill the tank, then let it stand upright for five to ten minutes so the cotton saturates fully. Firing a dry coil will instantly ruin it.

6. Start at the lower end of the coil's wattage band and build up gradually until the draw feels right.

What's in the Eleaf GTL Vape Coils Pack

Five Eleaf GTL replacement coils in your chosen resistance. No tank, pod or device is included, since these are replacement coils for a kit you already own.

About Eleaf

Eleaf is a long-running name in UK vaping, best known for the iStick and Pico ranges that put reliable, pocket-friendly kit in a lot of hands.

The GTL coil series is built around that same practical streak: a mesh element paired with organic cotton, offered across several resistances so one coil family can cover everything from a tight MTL pull to a wide-open DTL draw. It is straightforward hardware that does its job without fuss, which is why the GTL kits stay popular.

Stock Up and Save

Coils are a consumable, so buying a pack of five and keeping spares in the drawer is simply the sensible way to run any refillable kit. Pirate Vapes dispatches every order the same day before 4 pm, and regulars can top up through The Crow's Nest so fresh coils arrive before the old one gives out.

Every coil is a genuine Eleaf part, sold through an age-verified, over-18s checkout. Compare it against other Multi-Buy Vape Deals before you order.

Conclusion

The Eleaf GTL Vape Coils are the straightforward refill for anyone running a GTL Pod Tank or another compatible Eleaf kit. You get five genuine mesh coils, a choice of three resistances spanning MTL to DTL, and a push-fit design that makes swaps painless.

Match the resistance to your device and draw, keep a pack in reserve, and your kit keeps performing. Head back to Pirate Vapes to browse the wider range.

FAQs

How many GTL Vape Coils are in the pack?

Five. Each is the same resistance you select at checkout, so pick the value that suits your kit.

Which GTL Vape Coils resistance should I choose?

Match it to your draw: 0.4ohm for airy DTL, 0.8ohm as a versatile middle, 1.2ohm for tight MTL and nic salts.

Do GTL Vape Coils need screwing in?

No. The GTL coils are push-fit. Press the coil in until it sits flush, and the O-rings seal it in place.

Which devices do GTL Vape Coils fit?

A range of Eleaf GTL kits, including the GTL Pod Tank, Pico Compaq, iStick T80, iJust AIO and more. Check your exact model against the list above.

How long does a GTL Vape coil last?

It depends on wattage, e-liquid, and how often you vape. Higher-resistance coils generally last longer, while lower-resistance coils run hotter and wear faster.

How do I get the best flavour from a new GTL Vape coil?

Prime the cotton with a few drops, then let it sit filled for five to ten minutes before your first draw. Starting at a lower wattage helps too.