Geekvape Q V2 Replacement Pods

Geekvape Q V2 Replacement Pods

Geekvape Q V2 Replacement Pod Cartridges are 2ml refillable pods for the Q Series, supplied in packs of 3 with a built-in VPU mesh coil. The 2ml capacity is the UK limit for nicotine pods, and either nic salt or 50/50 freebase e-liquid is used to fill them.

Top-fill and side-fill designs are spread across six versions, with resistance running from 0.4ohm to 1.2ohm. Draw style follows the resistance, moving from restricted direct-to-lung at the low end to mouth-to-lung at the high end. A fresh pod is swapped into a Sonder Q, Wenax Q or Aegis Q kit in seconds, and no separate coil has to be fitted.

What to Know About the Geekvape Q V2 Cartridges

• 3 pods in every pack
• 2ml refillable pod with a built-in VPU mesh coil
• Top-fill and side-fill designs, six versions in total
• 0.4ohm to 1.2ohm resistances, from restricted direct-to-lung to mouth-to-lung
• Fits Q Series kits such as the Sonder Q2, Wenax Q2 and Aegis Q

Features of Geekvape Q V2 Replacement Pods

Every feature below sits inside the pod itself, so one swap renews the coil and the tank together. More pod options for other devices are listed in the Vape Pods range.

VPU Mesh Coil

Heat is produced by a mesh element under Geekvape's VPU technology, a flat woven surface rather than a round wire. The aim is even wicking and steady flavour from the first fill onwards. The coil is part of the cartridge, so a spent coil is replaced along with the pod and there is no separate part to buy.

Top-Fill and Side-Fill Options

Two filling styles are offered. Filling is done at the top of a top-fill pod and through the body of a side-fill pod. Side-fill is the only design offered for the 0.4ohm, top-fill is the only one for the 1.2ohm, and the 0.6ohm and 0.8ohm come in both. Each type holds the same 2ml of e-liquid.

Resistances From 0.4ohm to 1.2ohm

Wattage guidance rises as resistance falls. At 25 to 30W the 0.4ohm pod gives a restricted direct-to-lung draw, and the 0.6ohm does the same at 18 to 25W. The 0.8ohm offers a looser mouth-to-lung pull at 12 to 18W, while the 1.2ohm at 8 to 12W is the tightest.

Nic Salt and 50/50 Freebase Use

Both nic salt and 50/50 freebase are used in these pods, so liquid strength and style are left to the vaper. Salts are found in Nic Salts, while 50/50 E-Liquid covers freebase. Each pod takes up to 2ml per fill.

Leak-Resistant Structure

An upgraded leak-resistant structure is used in the V2 pod, with the shell and the internal design shaped to keep e-liquid inside. The port is closed fully after filling, and a short wait lets the coil absorb liquid before the pod goes into the device, which limits dry hits on the first draws.

Geekvape Q V2 Pod Resistance Options

Six versions are stocked by Pirate Vapes, each sold as a pack of three pods in one fill type.

#buttons

• 0.4 Ohm Side Fill
• 0.6 Ohm Side Fill
• 0.6 Ohm Top Fill
• 0.8 Ohm Side Fill
• 0.8 Ohm Top Fill
• 1.2 Ohm Top Fill

How to Swap the Q V2 Pod Cartridges

The routine is shared by both fill designs, and only the position of the port changes.

Step 1: Pull the spent pod off the device and open the pack.

Step 2: Unseal the port, which sits on the top or on the body depending on the version.

Step 3: Nic salt or 50/50 freebase is poured in, with the centre tube kept clear of liquid, and the fill is stopped at 2ml.

Step 4: The port is sealed completely, and the pod is left to stand briefly while the coil takes up the liquid.

Step 5: Press the pod into the kit until it seats in place.

Step 6: Take a few gentle draws before settling into normal use.

What's in the Q V2 Pod Cartridges Pack

One pack contains three pods, all in the same resistance and fill type.

• 3 x Geekvape Q V2 2ml refillable pod cartridges

A device and e-liquid are not included. Q Series kits are listed in the Refillable Pod Kits range.

Devices Compatible With the Q V2 Pods

The pods are made for Geekvape Q Series kits, including the Sonder Q, Sonder Q2, Wenax Q, Wenax Q2, Wenax Q Pro and Aegis Q. Sonder Q pods and other Q Series pods share one format, but fit varies by resistance.

A shared brand name is not a guarantee of fit. The 0.4ohm Side Fill pod is limited to fewer Q devices than the other versions, so it should be matched to the kit before it is ordered. Other Geekvape kits and pods are listed in the Geekvape Vapes range.

About Geekvape and the Q Series

Geekvape places the Q Series pod in several kits from different lines, including the Sonder, Wenax and Aegis families. The V2 pod carries improved VPU coil technology and is offered in both top-fill and side-fill forms across the resistance range.

Geekvape is also known for the rugged Aegis hardware, and the Aegis Q brings that build to a refillable pod format.

Stock Up and Delivery

A Sonder Q or Wenax Q device is kept going by a spare pack in the resistance it already runs. A second pack in another resistance changes the draw without a new kit. Multi-buy offers are collected in Multi-Buy Vapes, and orders over £40 go out as Free Pirate Post. An age check is part of every order at Pirate Vapes, and these pods are for over-18s only.

Conclusion

The Geekvape Q V2 cartridges suit owners of Sonder Q, Wenax Q and Aegis Q kits who want a refill in a chosen resistance, from the open 0.4ohm to the tight 1.2ohm. Six versions in packs of three make it simple to match the pod to the draw.

For chargers and cases, the Vape Accessories collection is the place to look, and Pirate Vapes has the rest of the range.

FAQs

Which kits do the Geekvape Q V2 pods fit?

They fit Geekvape Q Series kits including the Sonder Q, Sonder Q2, Wenax Q, Wenax Q2, Wenax Q Pro and Aegis Q. Fit varies by resistance, so the 0.4ohm Side Fill pod should be matched to its kit before ordering.

How many Q V2 pods come in one pack?

Each pack holds 3 pods of the same resistance and fill type. All six versions are sold in the same pack size, and no device or e-liquid is included.

What is the difference between top-fill and side-fill Geekvape Q pods?

The fill port is at the top of the pod on top-fill versions and on the side of the body on side-fill versions. Both hold 2ml. The 0.4ohm is side-fill only, the 1.2ohm is top-fill only, and the 0.6ohm and 0.8ohm come in both.

How do the 0.4ohm to 1.2ohm Q V2 cartridges differ in draw?

The 1.2ohm is the tightest option, drawing at 8 to 12W, and the 0.8ohm loosens the pull at 12 to 18W. Both the 0.6ohm (18 to 25W) and the 0.4ohm (25 to 30W) are restricted direct-to-lung.

What e-liquid can be used in Wenax Q pods from the Q V2 range?

Nic salt and 50/50 freebase e-liquid are both suitable, up to 2ml per pod. The pod should be left for a short while after filling so the coil can absorb the liquid.

Can the coil in the Geekvape Q V2 cartridges be changed on its own?

A separate coil is not offered for these pods. Each pod has its VPU mesh element fixed inside it, so the complete pod is swapped once the flavour fades, and that is why packs hold 3.