Horizon Tech Talons Replacement Pods | Pack Of 2

Horizon Tech Talons Replacement Pods

Five resistances, one pod family, and a compatibility map worth reading before you buy. The Horizon Tech Talons refillable pods come as a pack of 2, each a 2ml top-fill pod with a mesh coil and wood-pulp blended cotton inside.

The range stretches from a tight MTL draw all the way down to full sub-ohm direct lung, so the resistance you pick decides both how the pod vapes and which Talons device it belongs to. Grab the matching Replacement Pods for your kit, and you keep the same flavour and the same feel every refill.

Why vapers choose this:

• One platform, several draws. From a cigarette-style pull on the 1.0Ω to full sub-ohm clouds on the 0.2Ω, the same pod family covers both without swapping devices.

• Mesh with wood-pulp blended cotton wicks steadily and holds flavour cleaner, deeper into each pod.

• A 2ml top-fill design refills quickly from the top and keeps things tidy.

• Triple adjustable airflow fine-tunes how open or restricted the draw feels.

• Two per pack, so a fresh pod is always there when the flavour starts to fade.

Horizon Tech Talons Pods Features

The Resistance Is the Whole Point

Every pod in the range carries a sealed mesh coil, and the number printed on it sets the entire experience: the wattage it wants, the airflow that suits it, and the draw you get back. Pick low for clouds, high for a tight MTL hit. Get this one choice right, and everything else falls into place.

Mesh and Wood-Pulp Cotton, Working Together

The mesh heats across a broad, even surface, and the wood-pulp blended cotton behind it pulls liquid at a steady rate. Together they keep flavour consistent from the first fill to the last, and they handle sweeter liquids better than a plain round-wire coil would. Small detail, but you notice it across a week of use.

Fill It From the Top, Move On

A top-fill design means you lift the cap, add your e-liquid, and close it. No dismantling, no turning it upside down. Fair enough, most pods top-fill these days, but the swivel cap here is genuinely quick to work with.

Airflow You Can Actually Tune

The triple adjustable airflow is not a token slider. Close it right down for a snug MTL draw on the higher-resistance pods, or open it fully for the sub-ohm ones and let the air move through. Worth setting to taste before your first proper pull.

Match the Liquid to the Pod

Here is where people slip up. The MTL pods (0.8Ω and 1.0Ω) suit a 50/50 Nic Salts at up to 20mg. The sub-ohm 0.2Ω pods want a high-VG liquid at a much lower strength. Same range, two completely different bottles.

Horizon Tech Talons Pods Resistance Options

Six options on the shelf, spanning two vaping styles. Start from what you already vape and match up from there.

Most popular for MTL is the 1.0Ω at around 14W. Tight, cool, closest to a cigarette, and the natural home for a strong 20mg Nic Salt. Step up to the 0.8Ω at roughly 18W if you want a little more warmth and air while staying mouth-to-lung.

In the middle sits the 0.6Ω at about 25W. That is a restricted-lung draw with noticeably more vapour, comfortable on 50/50 or a slightly higher-VG blend.

Made for the Talons TW, the 0.4Ω runs around 32W for a warmer restricted-to-direct draw. This one is built for the TW rather than the earlier Talons, so check your device.

For sub-ohm clouds, there are two 0.2Ω pods, one on a Kanthal build and one on stainless steel. Both are direct-lung, higher-power, and want a High VG E-Liquid at low nicotine. Confirm your hardware can drive them before buying.

#buttons

• 0.2ohm Stainless Steel
• 0.2Ω Kanthal
• 0.4Ω
• 0.6Ω
• 0.8Ω
• 1.0Ω

How to Set Up the Talons Pods

Quick swap, then a bit of patience. The wait matters more than the swap does.

1. Pull the old pod off and click the fresh one firmly into place.

2. Flip open the swivel cap and add your e-liquid to the fill line. Match it to the pod: 50/50 for MTL, high-VG for sub-ohm.

3. Close the cap and rock the pod side to side so liquid reaches every part of the wick.

4. Stand it upright and leave it a full ten minutes for the sub-ohm pods, five for the MTL ones. The wood-pulp cotton is dense, and thicker high-VG liquid needs that extra time to soak through.

5. Take two or three gentle primer draws before you settle into it.

6. Set the airflow to taste, then vape.

What's in the Talons Pods Box

Two Talons pods in your chosen resistance, each with the mesh coil built in. No e-liquid, and no device. These are refills for a Talons you already own, so make sure the resistance matches your kit before the pack arrives.

Which Talons Device Do These Fit?

This is the part to get right, because the Talons pods are not one-size-fits-all across every model.

The 0.6Ω, 0.8Ω and 1.0Ω pods are the MTL and restricted-lung options, and the original Talons kit runs on these three. The 0.4Ω pod is built for the Talons TW and will not fit the earlier Talons. The two 0.2Ω sub-ohm pods are the direct-lung options for higher-powered hardware. This replacement range is also listed as fitting the Talons 2 and the Talons 3, so if you run one of those, check the resistance against your device rather than assuming every pod drops straight in.

When you reorder, match the exact resistance to your kit. Pirate Vapes lists each option on its own, and you can browse the full Refillable Pod Kits range if you are pairing pods to a new device.

About Horizon Tech

Horizon Tech, HorizonTech on most packaging, is a hardware maker known for pushing coil and wicking design, and the Talons pod range shows that streak. Rather than one fixed coil, the platform spreads across a range of resistances from sub-ohm right up to MTL, each using a mesh element paired with wood-pulp blended cotton for steadier wicking.

It is a flexible little system: one pod family, more than one device, and a draw for most tastes. Still choosing hardware? The Pod Kits range covers the devices these pods slot into.

Stock Up and Save

Pods are the running cost of any refillable setup, so keeping a spare pack in the drawer saves you a dry night waiting on a delivery. At two pods for a few pounds, it works out far cheaper per week than a disposable habit ever did.

Pirate Vapes dispatches every order the same day before 4 pm, and Free Pirate Post kicks in over £40. All stock is TPD compliant, age-verified at checkout, and over-18s only.

Conclusion

The Horizon Tech Talons replacement pods keep your kit running and let you change how it vapes just by switching resistance. Match the MTL pods to a 50/50 salt, the sub-ohm pods to a high-VG liquid, and the 0.4Ω to a Talons TW, and you have covered every draw the range offers.

Just confirm the resistance suits your exact device first. Browse more Refills And Pods, or head back to Pirate Vapes to top up your order.

FAQs

Which resistances fit the original Talons?

The 0.6Ω, 0.8Ω and 1.0Ω pods. The 0.4Ω is made for the Talons TW, not the earlier kit.

What liquid should I use with the Horizon Tech Talons pods?

Depends on the pod. The MTL pods take a 50/50 nic salt up to 20mg. The 0.2Ω sub-ohm pods need a high-VG liquid at low strength.

How many Horizon Tech Talons pods come in a pack?

There are two Horizon Tech Talons pods in one pack.

Can the 0.2Ω pods do proper clouds in a Horizon Tech Talons?

Yes. They are sub-ohm, direct-lung pods built for vapour, which is why they want high-VG liquid and a device that can push the power. Not one for a tight MTL draw.

Why does a new pod taste burnt?

Almost always firing it before the cotton is soaked. Fill, wait, then vape. High-VG liquid in the sub-ohm pods needs a good ten minutes, and a scorched wick will not recover.

Do Horizon Tech Talons pods fit the Talons 2 and Talons 3?

This range is listed as compatible with both. Match the resistance to how you want to vape, and check it against your device before ordering.