Innokin Endura M18 Vape Coils

Innokin Endura M18 Vape Coils

The Innokin Endura M18 Coils are the replacement heating element for the Endura M18 pod. Built as a 1.6 ohm BVC, they slot into the M18's refillable pod through a push-fit base: no unscrewing, no thread cleaning.

The M18 pod also accepts Innokin's older T18E coil for anyone crossing over from the earlier Endura T18 pen kit. Sits in the Vape Coils range as one of the more forgiving MTL replacement coils on the UK shelf, matched to 50/50 salts and higher-PG shortfills at the 10 to 13.5W output the M18 delivers.

Why vapers choose these:

• Direct replacement for the M18's included coil. No coil compatibility trial and error. If you own the Endura M18, this is the coil you refit.

• Push-fit base rather than screw-in threads, so coil swaps take about ten seconds without any liquid running down the pod threads.

• Bottom Vertical Coil layout wicks steadily from beneath the juice reservoir, which cuts down on dry hits mid-tank and keeps flavour consistent through the coil's life.

• T18E cross-compatibility on the M18 pod means anyone stepping up from the older T18 kit can keep their existing coil stock instead of buying twice.

• Organic cotton wicking delivers a clean, neutral base that lets fruit, menthol and dessert profiles come through without any off-taste from synthetic materials.

Innokin Endura M18 Coils Features

The Upgraded BVC Design

Innokin's Bottom Vertical Coil design has been in the Endura family since the T18 pen. The M18 version brings an upgraded vertical coil element inside the same physical footprint. The wick sits directly beneath the e-liquid channel, so gravity feeds juice straight into the cotton. In practice, that translates to fewer dry hits when the pod runs low, and more consistent flavour from first draw to last. Not revolutionary, but reliable, which is the point.

Push-Fit Coil Replacement

Swap the coil by pulling the pod off the device, twisting the base cap of the pod, pulling the spent coil out by hand, and pushing a fresh one in until it clicks. No threads to strip, no O-rings to lose, no residue to wipe. The whole process takes under a minute once you have done it once, which matters when you are getting out the door in the morning, and the flavour has just started to fade.

1.6Ω MTL Coil

The 1.6 ohm resistance is set to match the M18's fixed 10W output, with the coil handling the 13.5W boost mode without shortening its lifespan noticeably. This is deliberate. Innokin build BVC coils around a narrow, well-defined wattage window rather than trying to cover everything from pen to sub-ohm. The result is a coil that behaves the same way every session rather than one that peaks and fades quickly.

T18E Coil Compatibility

The M18 pod is designed to also accept the older T18E coil, which is Innokin's replacement coil for the Endura T18 II tank system. That opens up compatibility with existing coil stock for anyone upgrading from the pen-style Endura, and it means the M18 has two coil sources rather than one, which is useful for long-term supply. Pair the coils with any 10 or 20mg Nic Salt at the tighter airflow setting for the closest cigarette-style draw.

50/50 E-Liquid Compatibility

The 1.6 ohm coil is tuned for 50/50 salts and 50/50 shortfills rather than high-VG blends. Higher VG (60/40 and above) will wick too slowly through the BVC wick and cause dry hits, especially at 13.5W boost. Keep to salt at 10 or 20mg or a 50/50 shortfill from the 50/50 E-Liquids shelf, and coil life stays in the two-week-plus range.

Innokin Endura M18 Resistance Options

The M18 is a single-resistance system by design. The included coil in the kit and the standard replacement pack is the 1.6 ohm BVC. There is currently no lower- or higher-resistance variant in the M18 coil range, which keeps the system straightforward but limits fine-tuning.

#buttons

• 1.6 Ohm BVC

How to Fit the Innokin Endura M18 Coil

Quick swap. Around two minutes if you take your time with the prime.

1. Pull the pod off the top of the M18 and empty any remaining e-liquid.

2. Twist the base cap of the pod anti-clockwise to release it, then pull the spent coil out.

3. Drop five to six drops of e-liquid directly onto the cotton wick ports around the new coil.

4. Push the coil into the pod base until it clicks flat. Refit the base cap.

5. Refill the pod with your preferred 50/50 salt or shortfill.

6. Stand the assembled pod upright for around eight minutes before firing so the wick fully saturates. Skipping this step is the fastest way to burn a fresh coil.

What is in the Innokin Endura M18 Coils Pack

Each pack includes 5 genuine Innokin Endura M18 1.6 ohm replacement coils with an authenticity check code.

No e-liquid or replacement pods are included. Pair with any 10ml salt from the 10ml E-Liquids range and your Endura M18 pod kit for a full setup.

The Replacement Coil for the Innokin Endura M18 Pod Kit

The 1.6 ohm BVC coil is designed for the Innokin Endura M18 pod and nothing else. Not compatible with the T18 II tank, Zenith or Zenith II tank, Zlide tank, GO Z tank, or any Kroma-series device. If you own the M18 pod kit, this is the coil to buy.

Anyone still running a T18 pen may find the T18E variant is a better fit for that kit specifically, though the T18E will also fit the M18 pod as a secondary option. Coils sit in the wider Refillable Pod Kits accessory range at Pirate Vapes.

About Innokin BVC Coils

Innokin's Bottom Vertical Coil design predates most of the current mesh trend and has been through several iterations since the original Endura T18 launched in 2016. The BVC layout became a standard for MTL pen and pod kits because it delivers a consistent, predictable draw without needing constant priming or wattage adjustment.

Innokin also runs its own manufacturing rather than outsourcing, which is one of the reasons coil quality across the Endura family stays stable batch to batch. The M18 BVC represents the current generation of that coil, updated for the pod format and the M18's fixed-wattage output profile.

Stock Up and Save

The 1.6 ohm BVC coil typically lasts two to four weeks depending on how heavily you vape and what liquid runs through it. Sweet dessert and dark caramel profiles wear coils faster than fruit and menthol.

Keeping a spare pack of five in a drawer means you never lose an evening to a burnt wick. Consider setting up The Crow's Nest subscription for regular coil deliveries if the M18 is your daily kit, or grab an extra pack alongside a couple of bottles of salt to clear the free delivery threshold.

Pirate Vapes ships every order age-verified, dispatches same day on orders placed before 4 pm, and delivery is free with Free Pirate Post over £40. TPD compliant. Over 18s only.

Conclusion

The Innokin Endura M18 replacement coils do exactly what a good MTL coil should. Consistent flavour, straightforward push-fit installation, sensible lifespan, and cross-compatibility with the wider T18E range for anyone stepping over from the older Endura pen kit.

If you own an M18, keeping a pack on hand is the difference between a smooth vape and a burnt one. Pick up a pack at Pirate Vapes alongside a bottle of nic salt or one of the Replacement Pods if yours has picked up condensation. Sits comfortably alongside the rest of the Innokin Pod Kits accessory range.

FAQs

How long does the M18 coil last?

Typically two to four weeks depending on wattage mode, liquid type and daily use. Sweet dessert profiles wear coils faster than fruit or menthol. Prime properly and coils will run longer.

Can I use these coils in any other Innokin device?

No. The 1.6 ohm BVC coil is designed specifically for the Innokin Endura M18 pod. It will not fit the T18 II tank, Zenith, Zlide or Kroma devices.

Will T18E coils fit my M18 pod?

Yes. Innokin confirm the M18 pod accepts the T18E coil as a compatible alternative to the BVC. Useful for anyone upgrading from an older Endura T18 kit with existing coil stock.

What e-liquid should I use?

50/50 nic salt at 10 or 20mg, or a 50/50 shortfill at 3 to 6mg. Avoid high-VG 70/30 shortfills as they will not wick through the 1.6 ohm coil properly.

How do I know when to change the coil?

Muted flavour, a burnt taste even with fresh e-liquid in the pod, or gurgling on the draw are all signs. Change the coil rather than trying to push through, since a burnt coil can damage the wicking permanently.

Do I need to prime the coil before use?

Yes. Drop five to six drops onto the cotton ports, fit the coil, refill the pod and let it sit upright for around eight minutes before firing. Skipping this step burns coils immediately.