Nevoks A1 Replacement Pods - Pack Of 3

Nevoks A1 Replacement Pods

Four resistances in one range, from a 0.4ohm cloud pod down to a tight 1.2ohm for mouth-to-lung. The Nevoks A1 pods refill, so instead of binning a pod when the flavour goes, you fill this one again and only replace it when the built-in mesh coil finally tires.

Each pack holds three pods in the resistance you pick, all 2ml and built from tough PCTG with Australian cotton around the coil. They fit the Feelin A1, Feelin AX, and the wider Feelin A-series platform. If you run either, these Replacement Pods are the ones you want.

Why vapers choose this:

• Four resistances covering three draw styles. The 0.4ohm chases clouds, the 0.6ohm sits in restricted direct-to-lung, and the 0.8ohm and 1.2ohm keep things tight for mouth-to-lung, so one kit does the lot depending on which pod you load.

• Refillable, so the running cost drops. Fill from a bottle instead of buying prefilled.

• Built-in mesh coils heat quicker than old round wire and push flavour hard from the first few pulls.

• Australian cotton wicks fast and keeps dry hits rare.

• Two ways to fill depending on the pod: a side bung on the lower resistances and a top slot on the higher ones, both quick and clean.

Nevoks A1 Features

Mesh Coils, Sealed In

Every A1 pod has its mesh coil built into the shell. Mesh spreads heat over a wider area than coiled wire, which means faster ramp-up and cleaner flavour. There is nothing to screw in and nothing to prime separately. When the coil tires, the pod goes, and a fresh one takes its place.

Which Fill Port Do You Get?

It depends on the resistance. The 0.4ohm and 0.6ohm pods fill from a bung on the side. The 0.8ohm and 1.2ohm pods fill through a top slot once you lift the drip tip off. Both take a couple of seconds. Match your High VG E-Liquid or salt to the pod, and you are set.

Four Airflow Holes at the Base

Nevoks drilled a four-hole inlet into the bottom of each pod. More holes mean more air, which is why the lower resistances give a proper direct-to-lung draw. The higher resistances stay tighter for a cigarette-style pull. The pod itself sets the character rather than any switch on the device.

Keep the Leaks Where They Belong

The A1 pod uses a double-bottom shell that traps stray liquid before it reaches the battery contacts. Pods that leak wreck the device under them, and honestly, that is the fastest way to kill a pod kit. This one is built to hold the mess inside the pod where it cannot do damage.

Salt or Shortfill, Your Call

The range is happy with both. Nic salt in the 0.8ohm and 1.2ohm pods gives a smooth, satisfying MTL hit. Thicker Nic Salts suit the tighter pods, while a 70/30 shortfill feeds the airier 0.4ohm and 0.6ohm better. Pick the liquid to match the pod, not the other way round.

Nevoks A1 Resistance Options

Four to choose from, and the right one comes down to how you like to draw and what you fill it with. Here is where each sits.

#buttons

• 0.4 Ohm - Side Fill
• 0.4 Ohm - Top Fill
• 0.6 Ohm - Side Fill
• 0.6 Ohm - Top Fill
• 0.8 Ohm - Top Fill

How to Set Up the Nevoks A1 Pods

Under a minute once you know which port you have.

1. Match the pod to your liquid. High VG shortfill for the 0.4ohm and 0.6ohm, a 50/50 nic salt for the 0.8ohm and 1.2ohm.

2. Open the fill point. On the lower resistances, that is the bung on the side. On the higher ones, lift the drip tip to reach the top slot.

3. Drip two or three drops straight onto the exposed mesh first to wet the coil.

4. Fill to just below the max line, then reseal the bung or press the top back down.

5. Sit the pod upright and leave it for the better part of ten minutes so the Australian cotton draws the liquid all the way through. A dry first pull kills the coil on the spot.

6. Click it into your Feelin kit and take a few soft draws before your normal pulls.

What's in the Nevoks A1 Replacement Pod Pack Box

Three refillable A1 pods in the single resistance you choose, each with its mesh coil already built in. No e-liquid, no device, and no loose coils to fit. You supply the liquid and a Feelin kit to click them into, both easy to sort at Pirate Vapes.

Made for the Nevoks Feelin A-Series platform

These pods are cut for the entire Nevoks Feelin A-Series platform, covering the Feelin A1, Feelin AX, Feelin AR, Feelin AQ, Feelin AG, Feelin A2. All these kits share the exact same pod slot, so a pack bought for one works seamlessly across the others. If you are still choosing a device, browse refillable pod kits to pair with them.

They will not fit older non-A-Series Nevoks devices or any rival brand. The shell and connection are specific to the A-Series platform, so a pod from another kit will not click in. Stick to the A1 range to keep your Feelin A-Series kit running.

About Nevoks

Nevoks builds pod systems with a reputation for solid mesh coils and sensible, no-fuss design. The Feelin line is the brand's best-known range, and the A1 pod sits at the centre of it, giving a single low-wattage kit four different characters through its resistances.

Rather than chase gimmicks, Nevoks tends to focus on flavour, leak control, and battery management. The A1 pod is a good example of that: four resistances, two fill methods, one shared platform, and none of it complicated to live with.

Stock Up and Save

Refillable pods still wear out, and the coil inside sets the clock. Heavy vapers go through a pod every week or two, so a spare pack in the drawer saves the scramble. Set them up on The Crow's Nest and fresh pods land on schedule without you thinking about it.

Pirate Vapes dispatches every order the same day before 4 pm, and all hardware is TPD compliant with an age-verified checkout for over-18s only.

Conclusion

The A1 pods are the sensible refill for anyone running a Feelin A1 or AX. Three pods to a pack, four resistances spanning tight MTL to airy DTL, built-in mesh for quick, clean flavour, and two easy ways to fill.

When one fades, drop in a fresh pod and carry on. Browse the full range of Vape Pods and Vape Accessories at Pirate Vapes, and match your pod to the right liquid for the best of it.

FAQs

Which kits do the A1 pods fit?

The Nevoks Feelin A1 and the Feelin AX. Both use the same pod, so one pack covers either. Nothing else fits.

Are Nevoks A1 pods refillable?

Yes. Fill them from a bottle, vape, and refill until the built-in coil wears out. Then drop in a fresh pod.

How much do the A1 pods hold?

2ml, the UK limit. Enough for a decent stretch before a top-up.

Which Nevoks A1 resistance should I pick?

For a tight MTL draw with nic salt, go 0.8ohm or 1.2ohm. For more air and clouds, use the 0.6ohm or 0.4ohm with a high VG liquid.

How do I fill each Nevoks A1 pod?

The 0.4ohm and 0.6ohm fill from a bung on the side. The 0.8ohm and 1.2ohm fill through the top once you pull the drip tip.

How long does a Nevoks A1 pod last?

Depends on your liquid and how hard you vape. Sweet, high VG juice at higher power wears a coil faster. A week or two is typical.