SMOK M Series Replacement Coils

SMOK M Series Replacement Coils

Three mesh resistances, one pod system. The SMOK M-Coils are the replacement heads for the Tech247, sold in a pack of five and built on a mesh wire element for cleaner flavour and even heating. You get 0.4ohm, 0.6ohm, and 0.8ohm options, spanning DTL, RDTL, and a tighter MTL draw. Press-fit fitting means a swap takes seconds, and the unslotted base keeps seepage down.

If your Tech247 has started tasting burnt, these are the Vape Coils that bring it back. One of the tidier pod-coil designs SMOK has shipped, and it lands at Pirate Vapes ready to go.

Why vapers choose this:

• Genuine SMOK fitment. These are the coils the Tech247 was designed around, so the seating, the wicking, and the wattage all line up the way they should.

• Three draws from one pod. MTL, RDTL, or DTL, just by swapping the coil.

• Mesh, not wire. A bigger heating surface means sharper flavour and a slower burn.

• Press-fit. No screwing, no fiddling, ten-second swap.

• The unslotted base cuts the leaking that older pod coils were prone to.

SMOK M Series Coil Features

Mesh Where It Counts

The heating element is a full mesh sheet rather than a coiled wire. That spreads heat evenly across a wider area, so your e-liquid vaporises cleanly instead of scorching in hot spots. The payoff is sharper flavour and a coil that holds its taste for longer. Pair the tighter 0.8ohm with Nic Salts for the smoothest MTL result.

What Does Unslotted Actually Mean?

Most pod coils have slots cut into the base for liquid to feed through. The M-Coil seals that bottom off and wicks from the side instead. Fewer openings means fewer places for liquid to weep out, which is why the Tech247 stays cleaner in a pocket than a lot of pod kits manage.

One Coil, Three Vaping Styles

Swap between the three resistances and the whole character of the vape changes. The 0.4ohm opens up for direct-lung clouds. The 0.6ohm sits in the middle for a restricted lung hit. The 0.8ohm tightens right down for mouth-to-lung. Same pod, same device, a completely different draw.

Let the Tech247 Do the Thinking

Drop any M-Coil into a Tech247 on smart mode, and the IQ chip reads the resistance and sets the wattage itself. No menus, no guessing at numbers. Prefer control? Manual mode lets you dial within each coil's range. Either way, you are not fighting the device.

Built to Last a Little Longer

Mesh coils generally outlast old-style wire heads because the heat is spread out rather than concentrated in one spot. Stick to the recommended wattage and prime properly, and one M-Coil will comfortably see you through a week or two of daily vaping before the flavour starts to fade.

SMOK M Series Coils Resistance Options

Three mesh resistances, each tuned to a different draw. The wattages below are where each coil sits happiest, and the Tech247's smart mode will land on them for you.

Most popular: the 0.8ohm. This is the tight MTL coil, best at 11 to 14W. It suits nic salts and a cigarette-style draw, which is what most pod users are after. Start here if you are refilling with 10mg or 20mg salts.

The middle ground: the 0.6ohm. A restricted lung draw, or RDTL, running best at 15 to 18W. Warmer and airier than the 0.8 without going full cloud. A sensible step up if the tight MTL draw starts to feel restrictive.

For clouds: the 0.4ohm. The DTL coil, happiest at 19 to 22W, pushing the most vapour of the three with flavour to match. Pair it with a higher-VG juice from the High VG E-Liquid range to get the best from it.

#buttons

• 0.4 Ohm
• 0.6 Ohm
• 0.8 Ohm

How to Set Up the SMOK M Series Coils

Quick swap. Under two minutes once you have done it once.

1. Pull the spent M-Coil out of the Tech247 pod. It is press-fit, so it lifts straight out with a firm tug.

2. Take a fresh coil and drip three or four drops of e-liquid onto the exposed mesh ports on the side of the coil.

3. Line the new coil up with the pod's coil chamber and press it in firmly until it seats flush.

4. Fill the pod, refit it, and add a drop or two down the centre if the wick still looks dry.

5. Stand the filled pod upright for a solid seven minutes so the mesh saturates fully before your first pull.

6. Start low. On smart mode, the Tech247 sets the wattage; on manual, begin at the bottom of the coil's range and build up.

What's in the SMOK M Series Coil Box

Five M-Coils in your chosen resistance. That is it: no pod, no device, and no e-liquid. Just the coils, ready to press into a Tech247 pod cartridge.

Made for the SMOK Tech247 Pod System

These are M-Coils, built for one platform: the SMOK Tech247. They press-fit into the Tech247 pod cartridge and slot straight into the Refillable Pod Kits in that line. Keep a set of spare Replacement Pods next to them, and you have a full refresh for when the old pod finally wears out.

What they will not fit: SMOK's RPM, Nord, TFV, or any other coil platform. The M-Coil is specific to the Tech247 system. If the coil currently in your pod is not marked M, this is not the replacement you want.

About SMOK

SMOK has been building coils for well over a decade, and the M-Coil is one of its more recent mesh designs. The unslotted bottom is the interesting part: instead of the usual cut-outs, the base is sealed and the coil wicks from the side, which cuts down the seepage that plagued older pod coils.

Paired with the Tech247's smart chip, the mesh runs at the right wattage without you touching a dial. It is a straightforward, reliable coil built for one job. Browse the full SMOK Coils range for other fitments.

Stock Up and Save

Coils are the one part you replace on a schedule, so it pays to keep a pack ahead. A five-pack of M-Coils covers most vapers for a month or more, depending on how heavy you go. Order two, and you are set for the season.

Every order from Pirate Vapes ships the same day before 4 pm in padded packaging. All stock is TPD compliant, with an age-verified checkout and over 18s only. Free Pirate Post over £40.

Conclusion

The SMOK M-Coils are the genuine replacement for the Tech247, nothing more complicated than that. Three mesh resistances covering MTL through DTL, a leak-resistant unslotted base, and a press-fit fitting that takes seconds.

If you run a Tech247 and the flavour has dropped off, a fresh five-pack brings it back. Grab your resistance and pick up more Vape Accessories at Pirate Vapes.

FAQs

Which device do the M-Coils fit?

The SMOK Tech247 pod system. They press-fit into the Tech247 pod cartridge. They do not fit RPM, Nord, or TFV coils.

What resistances are there in the M-Coils?

Three: 0.4ohm, 0.6ohm, and 0.8ohm, all mesh. DTL, RDTL, and MTL, respectively.

Which M-coil resistance is best for nic salts?

The 0.8ohm. It runs at 11 to 14W for a tight MTL draw, which suits 10mg and 20mg salts.

How long does an M Series coil last?

Usually one to two weeks per coil with daily use. Sweeter liquids gunk the mesh faster, so darker, sugary flavours shorten it.

Do I need to prime the M-Coils?

Yes. Wet the wicking ports, fill, and leave it a few minutes before firing. Skip that, and you will burn the coil on the first pull.

Does the Tech247 set the wattage itself?

On smart mode, yes. The chip reads the coil and picks the wattage. Manual mode lets you set it within the coil's range.