Vaporesso MTX Replacement Coils

Pure MTL. That is what the Vaporesso MTX coil range was built for. Three resistance options, all sitting above 0.8ohm, all designed for low-wattage mouth-to-lung vaping with nic salts or 50/50 blends.

The 0.8ohm gives a slightly warmer draw, the 1.2ohm runs at 8-12W for a cooler cigarette-style pull, and the 1.4ohm goes even tighter for the lightest possible wattage. Press-fit installation, five coils per pack. Designed for Vaporesso's GEN FIT kit and compatible MTL tanks.

Why vapers choose the MTX Coils:

• Dedicated MTL design gives a draw that genuinely feels like a cigarette, not a watered-down version of a DTL coil at low wattage

• Three resistances above 0.8ohm let you fine-tune the tightness of your draw without leaving the MTL range

• Low-wattage operation at 8-12W extends battery life significantly compared to sub-ohm coils, which matters on smaller devices

• Press-fit installation makes the swap quick and clean, no mess, no disassembly

• Pairs perfectly with nic salts at 10-20mg in 50/50 blends, which is exactly what most UK MTL vapers are using

MTX Replacement Coils Features

Built From the Ground Up for MTL

A lot of coil ranges treat MTL as an afterthought. They make a sub-ohm coil, bump the resistance, and call it mouth-to-lung. The MTX is different. Vaporesso designed this coil specifically for tight-draw vaping, and you can feel the difference. The airflow restriction, the wicking speed, the wattage ceiling: all of it is calibrated for e-liquid at 50/50 and nic salts at 10-20mg.

Low Wattage, Long Battery

Running at 8-12W on the 1.2ohm means your device battery stretches much further between charges. That is a practical advantage on the GEN FIT and similar compact kits. If you carry your vape to work and do not want to worry about charging by lunch, a low-wattage MTL coil is the reason that works.

Three Resistances, Same Tight Draw

The 0.8ohm sits at the warmer end of MTL. Slightly more vapour, a touch more throat. The 1.2ohm is the middle ground and the one Vaporesso markets as the standard. The 1.4ohm pulls the wattage down even further for the tightest, coolest draw in the range. All three are genuine MTL territory.

Press-Fit Keeps It Simple

No threading. No alignment fiddling. The MTX coil pushes straight into the base and seats itself. Pull the old one out, press the new one in. If you have used threaded coils before and found the process annoying, this is a noticeable improvement. Ten seconds, done.

Nic Salt Ready From the Box

These coils are sized and wicked for 50/50 nic salts. The wicking ports are narrow enough to prevent flooding at low wattage but wide enough to keep up with regular use. You do not need to break them in for half an hour wondering if the wick can handle the liquid. Fill, prime, vape.

MTX Replacement Coils Resistance Options

Three options. All MTL. The choice is about how tight and how cool you want your draw.

Most popular: the 1.2ohm at 8-12W. This is the one Vaporesso highlights as the standard MTX coil. Cool draw, tight restriction, clean flavour from nic salts. If you are coming from cigarettes or from a disposable vape, this resistance will feel the most familiar.

Warmest option: the 0.8ohm. Still MTL, but you get a touch more warmth and vapour production. Better for vapers who find 1.2ohm a little too cool or who want slightly more throat hit from their nic salt.

Tightest draw: the 1.4ohm. Lowest wattage, coolest vapour, least visible cloud. If discretion matters or you just prefer the absolute minimum vapour output, this is the one.

#buttons

• 0.8ohm
• 1.2ohm
• 1.4ohm

How to Set Up the MTX Replacement Coils

Quick swap. Under two minutes including the wait.

1. Remove the pod or tank section from your device.

2. Pull the old MTX coil straight out of the base. Press-fit, so it comes out with a gentle pull.

3. Take a fresh coil from the pack. Drop two to three drops of e-liquid onto the cotton visible through the side ports.

4. Press the new coil firmly into the base until you feel it seat.

5. Reassemble and fill with e-liquid. Tilt the filled unit gently from side to side a few times, then leave it upright for about three minutes before the first draw.

6. Start at the low end of the wattage range and take a few gentle pulls before settling in.

What's in the MTX Replacement Coils Box

Five coils in your chosen resistance, plus a user manual. No e-liquid, no device, no pod. Just the coils and the manual.

The MTL Coil for Vaporesso's GEN FIT Range

The MTX coil platform was developed alongside the Vaporesso GEN FIT kit. That is its primary home. The coil dimensions, wicking design, and press-fit base are all engineered around how the GEN FIT's MTL Tank operates.

If you own a GEN FIT, these are your replacement coils. If you own a different Vaporesso Device, check whether it uses the MTX coil type before ordering. Vaporesso runs several coil platforms across its range, including GTX and COREX, and they are not interchangeable. The MTX is its own system.

About Vaporesso

Vaporesso has been designing coil platforms since the early days of regulated vaping. The AXON chipset, the COREX heating system, the GTX coil range: each one came from the same R&D approach of building coils that suit specific vaping styles rather than trying to make one coil do everything.

The MTX sits in the pure MTL corner of that lineup. While most of Vaporesso's attention goes to the XROS series and the LUXE pod mods, the MTX coil is a quieter product. But for Vaporesso users who want a genuine cigarette-style draw, it does exactly what it is supposed to.

Stock Up and Save

Five coils per pack. At 8-12W, each one tends to last longer than a sub-ohm coil since the wattage is so low. Still, keeping a spare pack in the cupboard means you are never caught short when the flavour starts dropping off mid-week.

Every order from Pirate Vapes ships the same day before 4 pm in padded packaging. All stock is TPD compliant, with an age-verified checkout, over-18s only. Free Pirate Post on orders over £25.

Conclusion

The MTX coils deliver genuine MTL vaping at low wattage, with three resistance options that let you dial the draw tightness exactly where you want it. If you own the GEN FIT or another compatible Vaporesso MTL setup, these are your coils.

Straightforward press-fit swap, five per pack, and priced sensibly for what is essentially a specialist MTL product. Browse more Vaporesso Coils and vape accessories at Pirate Vapes.

FAQs

What devices work with the MTX coils?

The Vaporesso GEN FIT is the confirmed compatible device. Vaporesso runs multiple coil platforms across its product range, so always check whether your specific device uses MTX coils before purchasing.

What resistance should I pick for nic salts?

The 1.2ohm is the standard recommendation. Cool draw, tight airflow, works well with 50/50 nic salts at 10-20mg. If you prefer slightly more warmth, the 0.8ohm is worth trying.

How long do the MTX coils last?

Longer than most coils, honestly. Low wattage at 8-12W puts less stress on the coil than sub-ohm use. With regular daily vaping and non-sweet liquids, expect one to two weeks per coil. Maybe more.

Can I use freebase e-liquid with MTX coils?

You can, though they are optimised for 50/50 nic salts. Freebase at 50/50 VG/PG will work fine. Avoid high VG blends (70/30 or above) as the narrow wicking ports on MTL coils struggle with thicker liquids.

Are MTX coils the same as GTX coils?

No. Different platform entirely. GTX coils are Vaporesso's broader coil system covering MTL through DTL. The MTX is a standalone range for pure MTL use, and the two are not interchangeable.