Geekvape Z Max Sub Ohm Replacement Tank

Top airflow in, vapour out, nothing leaking from the bottom. That is the short version of what the Geekvape Z Max Sub Ohm Replacement Tank does differently. Where most sub-ohm tanks pull air up through the base and eventually let juice follow it, the Z Max sends air downward from the top, around the coil, and out the drip tip. Paired with Geekvape's M Series mesh coils, you get a DTL Tank that chases clouds properly without turning the base of your mod into a sticky mess. 

Pirate Vapes carries the Z Max in all six colours, genuine Geekvape, 2ml TPD-compliant, shipped tracked and age-verified across the UK. If you have been burning through sub-ohm tanks that leak, flood, or just stop tasting right after a week, give this one a look. 

Why vapers choose this:

• Top-to-bottom airflow routes around the coil, helping reduce leakage at the base compared to bottom-airflow tanks.

• Press-fit coil system. No threading, no screwing. Old coil out, new coil in.

• Quarter-turn top fill with dual ports wide enough for most bottle nozzles. Quick, clean, no mess.

• Standard 510 connection. Works with the vast majority of regulated box mods.

• Stainless steel and Pyrex glass that hold up to the kind of daily wear that cracks cheaper tanks.

Geekvape Z Max Sub Ohm Replacement Tank Features

Top-to-Bottom Airflow That Keeps the Base Dry

Bottom-airflow tanks leak. Not all of them, not every time, but enough of them often enough that most sub-ohm vapers have a sticky mod story. Condensation collects at the base, pools around the coil housing, eventually finds its way onto your 510 connection. You have probably wiped yours down more times than you can count.

The Z Max avoids most of that by pulling air in from the top instead. Slotted inlets near the cap send air downward around the coil, and it exits through the 810 drip tip. Moisture stays near the top where it evaporates rather than settling at the base where it causes problems. Is it perfectly leakproof in every scenario? No tank is. But the difference is real, and you notice it the first time you pick up your mod after an overnight sit and the base is still clean.

Press-Fit Coil Swaps

Threading a coil into a sub-ohm tank is one of those small annoyances that adds up. Cross-thread it once and you are either fighting to unscrew the thing or dealing with a flooded deck for the rest of the afternoon. The Z Max skips all of that. Push the old coil out from the base, press the fresh one firmly into place.

Seal forms as the coil seats itself. Replacing a coil takes only a few seconds and you do not need to drain the tank first. If you have ever emptied 2ml of juice into a tissue because your old tank needed a full disassembly to swap coils, you know why this matters. Keep spares on hand from the Vape Coils collection.

M Series Mesh Coils

Two coils in the box. The 0.14 ohm single mesh handles 60 to 80W. The 0.2 ohm triple mesh covers 70 to 85W. Both are physically larger than the Z Series coils from other Zeus tanks, which gives them more mesh surface area and better contact with the cotton.

What does that actually do? More even heating from the first draw to the last, with less of that flavour drop-off you sometimes get near the bottom of the tank on traditional wire builds. Both coils are designed for High-VG E-Liquids when properly primed. M Series only, by the way. Z Series coils from other Zeus tanks will not fit.

Quarter-Turn Top Fill

Twist the cap a quarter turn. Two large fill ports. Pour. Twist shut. That is the whole process. No silicone tabs to wrestle open, no sliding doors that gunk up after a fortnight. The ports are wide enough for most dropper and squeezer bottle nozzles, so you are not trying to aim a thin stream into a pinhole while juice runs down the side. After dealing with tanks that turn refilling into a five-minute chore, a clean top-fill system almost feels like a luxury. It should not, but it does.

Solid Build, Six Finishes

Stainless steel. Pyrex glass. Gold-plated 510 pin for reliable conductivity. Measures 26mm at the base and roughly 32mm at the widest, so it looks right on larger dual-battery mods but may overhang a touch on compact single-battery devices. Worth checking your mod width before ordering if that sort of thing bothers you. Six colour options let you match your setup or clash with it on purpose. People who have been running one for six months or more tend to say it still looks and performs the way it did out of the box. For a tank at this price, that is saying something.

Geekvape Z Max Sub Ohm Replacement Tank Colour Options

You fill this tank yourself, so there are no flavour variants. The only decision is finish. Pirate Vapes stocks all six.

#buttons

• Black
• Gunmetal
• Silver
• Blue
• Gold
• Red

Same internals across every colour. Pick whatever looks right on your mod and move on.

How to Set Up the Geekvape Z Max Sub Ohm Replacement Tank

1. Unscrew the base. The 0.14 ohm coil comes pre-installed. Want to start with the 0.2 ohm triple mesh instead? Push the pre-installed one out and press the spare firmly into place.

2. Prime the coil. Three or four drops of e-liquid directly onto the cotton visible through the wicking ports. This saturates the wick before your first draw and helps the coil last longer.

3. Screw the base back on. Finger-tight is plenty.

4. Quarter-turn the top cap to open the fill ports. Pour in your preferred high-VG juice from the E-Liquids Collection. Leave a small gap at the top.

5. Close the cap firmly.

6. Stand it upright for five to ten minutes. Seriously. Do not skip this. Vaping on dry cotton is the fastest way to ruin a brand new coil and throw money away.

7. Thread it onto your 510 mod. Set wattage within the coil's range. 60W for the 0.14 ohm. 70W for the 0.2 ohm. Start at the low end and work up.

8. Take a few shorter draws before going full lung. First few pulls let the cotton settle in and the flavour come through properly.

What's in the Geekvape Z Max Sub Ohm Replacement Tank Box

Tank, two coils, small bits. No mod, no batteries, no juice.

• 1 x Geekvape Z Max Sub Ohm Tank

• 1 x M Series 0.14 ohm Single Mesh Coil (pre-installed), rated 60 to 80W

• 1 x M Series 0.2 ohm Triple Mesh Coil, rated 70 to 85W

• 1 x 810 Drip Tip

• 1 x Spare Parts Pack

• 1 x User Manual

Two coil types straight out of the box. Try both, figure out which wattage range you actually like, then buy a five-pack of whichever one wins.

Made for Serious 510 Mods

Standard 510 thread. Sits on most regulated box mods without adapters, spacers, or anything awkward. Geekvape designed this tank to pair with the L200 Classic (Aegis Legend 2), a dual 21700 mod that pushes up to 200W. That combo is hard to fault. But you are not locked into it. Any regulated mod pushing between 60W and 85W will drive the included coils properly.

Compatible devices:

• Geekvape L200 Classic (Aegis Legend 2)

• Geekvape Z200 (Zeus 200)

• Most regulated 510-threaded mods capable of the recommended wattage

Compatible coils:

• Geekvape M Series Coils (0.14 ohm single mesh, 0.2 ohm triple mesh, plus other variants in the M Series family)

M Series and Z Series coils are not interchangeable. Check before you order. If you need a mod to run this tank, browse the Vape Mods collection for dual-battery options that match.

About Geekvape

Started in 2015 in Shenzhen. Small team. One goal: build vaping hardware that survives real life without compromising on performance. The Aegis series is what made the name. Water-resistant, dust-resistant, shock-resistant, tested to actual industrial standards rather than just printed on a box. That reputation stuck. They have spent the decade since expanding into tanks, pods, coils, and full kits, and the Zeus tank family is probably their most well-known sub-ohm line at this point.

The Z Max sits within that range and uses their newer M Series coils for improved cloud and flavour. Geekvape Products are sold in more than 70 countries. Multiple design awards, including a Red Dot. They build stuff that lasts.

Stock Up and Save

Two coils gets you going but they are not going to last the month. A five-pack of M Series coils alongside your tank keeps you sorted for a decent stretch without scrambling for replacements halfway through. Pirate Vapes packs every order with care, ships tracked via Royal Mail across the UK, and age-verifies every checkout.

Our Geekvape stock is genuine, properly sourced, TPD-compliant. Browse the full Vape Tanks collection if you want to weigh up your options before committing. No grey market hardware. No fakes. Just properly handled gear dispatched same day when you order before the cut-off.

Conclusion

Top airflow keeps the base dry. Mesh coils pull real flavour. Press-fit swaps take seconds. That covers the essentials of what the Geekvape Z Max Sub Ohm Replacement Tank does, and it does all three without making you fuss over it.

Six colour finishes, two coils included, a 510 thread that works with practically anything above 60W, and a build that holds together long after cheaper tanks start rattling. 

If you want a DTL tank that stays leak-free and tastes right for more than a week, the Z Max earns its spot. Grab one from Pirate Vapes with fast, age-verified UK delivery.

FAQs

Does the Geekvape Z Max Sub Ohm Tank leak?

The top-to-bottom airflow keeps juice away from the base, which is where most tanks start leaking. Close the airflow when refilling, keep the cap tight, and issues are rare. No tank is perfectly leakproof under every single condition, but this one comes closer than most bottom-airflow designs out there.

What coils does the Geekvape Z Max use?

M Series only. A 0.14 ohm single mesh (60 to 80W) and a 0.2 ohm triple mesh (70 to 85W) come in the box. Five-packs of each are sold separately.

Will the Z Max fit my mod?

Got a 510 thread and 60W or more? It should work. Bear in mind the tank is 32mm at its widest, so it pairs best with larger dual-battery mods. Smaller single-battery setups may see a bit of overhang.

What e-liquid should I use?

High-VG. 70/30 or thicker. Mesh coils running at 60W and above need that viscosity to wick properly and produce the clouds they are designed for. Nic salts are not a good fit here. They are made for lower-powered MTL setups and the throat hit at these wattages would be rough.

Is this the same as the Zeus tank?

Same family, different coils. The Z Max takes M Series coils. Other Zeus tanks use Z Series coils. They do not fit each other. Always check the coil type before you order replacements.

Can I use 50/50 e-liquid?

Not really designed for it. Thinner juice wicks faster than the coil is built to handle, and you might notice some spitting or uneven vapour production. 70/30 VG/PG or higher gives the best results with this tank.

How long do the coils last?

Depends on your wattage, your juice, and how hard you chain-vape. Sweeter liquids gunk mesh up faster than anything else. When the flavour drops off or starts tasting papery, swap it out.