HorizonTech Sakerz Replacement Coils

HorizonTech Sakerz Replacement Coils

Three mesh resistances, one press-fit fitting, sold in packs of three. The HorizonTech Sakerz Replacement Coils cover the full draw range for the Sakerz sub-ohm tank, from the flavour-forward 0.17Ω 2-in-1 mesh through the cloud-heavy 0.16Ω down to the cooler, lower-power 0.4Ω.

These are direct-to-lung (DTL) coils built for high-VG juice, and they drop straight in without any screwing about. If you run the Sakerz or Sakerz Master and your flavour has gone flat, a fresh set of HorizonTech Coils is the fix. Every order from Pirate Vapes ships in plain, padded packaging.

Why vapers choose this:

• The 0.17Ω 2-in-1 mesh is the standout. Its dual-layer mesh spreads heat across a wider surface, which is why most Sakerz owners rate it as the best balance of taste and vapour in the range and treat it as their daily coil.

• Press-fit fitting. No threads to cross, no fiddling. Push it in and go.

• Three resistances in one range so you can shift between denser clouds and a cooler, softer draw without changing tanks.

• Built for high-VG juice. Thicker liquids wick and vaporise properly here.

• Packs of three keep a couple of spares in the drawer for when the flavour starts to fade.

HorizonTech Sakerz Coils Features

Mesh and Wood Pulp Wicking

A mesh strip heats faster and more evenly than old-style wound wire, but the real secret here is the wicking. HorizonTech uses a signature wood pulp and cotton blend that absorbs liquid incredibly fast. Across all three Sakerz resistances, this combination of mesh and wood pulp is what gives these coils their reputation with cloud chasers, delivering sharper flavour and thicker vapour from the first pull, especially when paired with a proper high VG e-liquid.

Easy Press-Fit Replacement

Ever cross-threaded a coil and killed the seal? Press-fit removes that risk entirely. The coil pushes into the base of the tank and seats on its O-rings, so installation takes seconds and there is far less to get wrong. Honestly, once you have used a press-fit system, going back to screw-in coils feels like a chore.

Three Coil Options for Different Draws

The range covers real differences in feel. The 0.16Ω pushes the most vapour and gets through juice quickest. The 0.17Ω 2-in-1 sits in the sweet spot for everyday use. The 0.4Ω runs cooler at 40W for a lighter, more restricted DTL hit. Pick the one that suits your mood or your mod.

Designed for High-VG E-Liquid

These coils want a high-VG blend, ideally 70% VG or more. Thin 50/50 salts will flood a sub-ohm mesh coil and taste weak, so keep those for a pod device. Reach for a shortfill instead, and the wicking keeps up without dry hits.

Long-Lasting Coil Performance

Coils are consumables. Flavour dulls, and vapour drops off as the mesh ages, usually after a week or two of regular use. Having the next coil ready means you are never stuck with a burnt taste mid-week waiting on a delivery.

HorizonTech Sakerz Coils Resistance Options

The Sakerz range gives you three genuinely different experiences, so it is worth knowing which suits your setup before you buy.

Start with the 0.17Ω 2-in-1 mesh if you are unsure. This is the flagship of the range and the one most Sakerz owners come back to. The twin-mesh interior widens the heated area, which lifts flavour and vapour together, and it runs comfortably at 70W with high-VG juice. For most people, this is the daily driver.

The 0.16Ω single mesh is the cloud option. It puts out the biggest plumes in the range and runs at 70W, with the trade-off that it drinks through e-liquid faster. Pick this one if maximum vapour matters more than coil longevity.

The 0.4Ω mesh is the outlier and the gentlest of the three. Rated up to 40W, it gives a cooler, slightly tighter DTL draw that suits lower-powered mods or anyone who finds the 70W coils a bit much.

#buttons

• 0.16 Ohm
• 0.17 Ohm 2-in-1
• 0.4 Ohm

How to Set Up the Sakerz Coils

Quick job. Under two minutes.

1. Turn your Sakerz tank upside down and unscrew the base to reach the coil housing. (Because it is a top-airflow tank, keeping it inverted means you don't need to empty your e-liquid).

2. Pull out the old coil from the base. It lifts straight off, no wrench needed.

3. Trickle 4 to 5 drops of your e-liquid onto the exposed cotton ports of the new coil so the wick starts off wet.

4. Press the fresh coil firmly into the base until it seats on its O-rings, then screw the base back on.

5. Fill with high-VG juice and stand the tank upright for a full 5 minutes so the cotton saturates completely before you fire it.

6. Begin low and climb. Take a few gentle pulls at a modest wattage, then work up towards the coil's rating.

What's in the Sakerz Coils Box

Each pack contains three HorizonTech Sakerz mesh coils in your chosen resistance. That is the lot: three coils, ready to fit. There is no tank, no e-liquid, and no device included, so you will need your Sakerz or Sakerz Master tank and a bottle of high-VG juice to go with them.

The Sub-Ohm Coil Made for the Sakerz Tank

These are single-tank coils, purpose-built for HorizonTech's Sakerz sub-ohm platform. They fit the original Sakerz tank. They also fit the Sakerz Master tank. Both use the same press-fit housing, so the full range of resistances is interchangeable between the two.

What they will not do is fit anything else. This is not a universal coil, so it will not seat in other sub-ohm tanks. Running a different setup? Check the broader Sub-Ohm DTL Tanks to match coils to your own hardware, and keep a Spare Tank Glass in the drawer while you are at it.

About HorizonTech

HorizonTech built its name on sub-ohm mesh coils long before mesh became the default. The brand's Falcon series helped set the standard for flavour-focused DTL vaping, and the Sakerz line carries that engineering across to a tank aimed at balance rather than sheer size.

The 2-in-1 mesh element in the flagship coil is HorizonTech's own design, splitting the heated surface into two layers for a fuller draw. It is a coil range with a loyal following in the UK, and the Sakerz tank remains a solid pick for anyone chasing dense vapour and clean taste.

Stock Up and Save

Coils are a running cost, not a one-off, so it pays to keep a set ahead. Grab a couple of packs, and you are covered for weeks rather than reordering every time the flavour drops.

Pirate Vapes dispatches every order the same day when it is placed before 4 pm, sent in discreet padded packaging. Checkout is age-verified, all stock is TPD compliant, and it is over-18s only. Pair a pack with a high-VG shortfill, and you are set.

Conclusion

The HorizonTech Sakerz coils are a straightforward, well-proven set for one job: keeping a Sakerz or Sakerz Master tank running at its best. The 0.17Ω 2-in-1 is the coil to start with for flavour and vapour together, the 0.16Ω is there when you want maximum clouds, and the 0.4Ω gives a cooler, lighter draw for lower-powered setups.

Press-fit fitting makes swaps painless, and a pack of three keeps spares on hand. Stock up alongside your other Vape Accessories and pair them with a 70/30 Shortfill at Pirate Vapes.

FAQs

Which Sakerz coil should I buy first?

The 0.17Ω 2-in-1 mesh. It is the flagship of the range and gives the best balance of flavour and vapour at around 70W. The 0.16Ω is the pick if you want bigger clouds instead.

Do Sakerz coils fit the Sakerz Master tank?

Yes. They fit both the original Sakerz tank and the Sakerz Master tank, which share the same press-fit housing. They do not fit any other tank.

How long does a Sakerz coil last?

Usually one to two weeks of regular use, depending on your wattage and how sweet your juice is. Dark, sweetened liquids shorten coil life. A pack of three keeps spares ready.

What e-liquid works best with Sakerz coils?

A high-VG blend at 70% VG or above. Sub-ohm mesh coils need thicker liquid to wick properly. Avoid thin 50/50 nic salts, which are better suited to pod kits.

How do I fit a Sakerz coil?

It is press-fit, so no threading. Drip a little juice onto the cotton, push the coil into the tank base until it seats, fill up, and rest it for five minutes before vaping.

Why is the 0.4Ω rated lower than the others?

Because it is the cooler, gentler coil in the range. At up to 40W it gives a softer, slightly tighter DTL draw, which suits lower-powered mods and vapers who find 70W too warm.