OXVA Origin X 510 Adaptor 

One small accessory that genuinely changes what the Origin X can do. Snap this adaptor onto your OXVA Origin X in place of the pod, and you have got a 510-thread mod capable of running tanks and rebuildables up to 24mm wide. It keeps the same magnetic connection as the stock pod, so fitting it takes seconds and no tools.

Gold-plated contacts keep the connection clean, and the mod still reads your coil as it always did. If you already own the Origin X and want more flexibility from it, this is a sensible purchase.

Why vapers choose this:

• Turns a pod mod into a 510 thread mod without buying a new device

• Same magnetic click-fit as the stock pod, swapped in seconds

• Gold-plated contacts hold up better than bare metal over time

• Supports tanks and rebuildables up to 24mm without overhang

• Costs very little for how much flexibility it adds to the Origin X

OXVA Origin X 510 Adaptor Features

Magnetic Fit, Same as the Pod

No screws, no threading onto the mod itself. The adaptor connects to the Origin X exactly the way the pod does, so there is nothing new to learn. Pull the pod off, press the adaptor on, and you are done. Swapping back to pod mode later takes the same two seconds in reverse.

Gold-Plated Contacts

Bare metal contacts corrode and lose conductivity with repeated use. Gold plating resists that, which means a cleaner, lower-resistance connection between the mod and whatever tank you have threaded in. The Origin X chipset reads coil resistance through it exactly as it would through the stock pod, with no drop in performance.

24mm Diameter Support

Most mainstream sub-ohm and MTL tanks sit at 22mm to 24mm, and this adaptor covers that range without anything sitting proud of the mod's deck. A 22mm tank fits flush, and 24mm fits without issue. Anything wider will overhang the body, so it is worth checking your tank's diameter before ordering.

Expands What the Origin X Can Run

The Origin X puts out up to 60W and handles builds from 0.15 to 2.0ohm on its own, so most sub-ohm tanks, MTL Tanks, and rebuildable atomisers fall comfortably within that window. Fit the adaptor, and the same 18650 mod you already own works with gear that would otherwise need a separate box mod.

Simple, No-Tool Installation

There is nothing to assemble here. The adaptor is a single piece that clicks onto the magnetic contacts and accepts a standard 510 thread on the other end. Thread your tank in, power the mod on, and it reads the coil automatically. No firmware updates, no extra cables, no fiddly setup. Pirate Vapes stocks it alongside the rest of our Vape Accessories range, so it is easy to add to an existing order.

Compatible Tanks & Atomisers

Once fitted, the adaptor opens the Origin X up to standard 510 gear rather than being locked into OXVA's own pods. It is worth knowing what actually works well with it before you order a tank to go with it. Pirate Vapes carries a wide range of Vape Tanks that suit the Origin X once the adaptor is fitted.

Best matches:

• Sub-ohm tanks in the 22 to 24mm range, run comfortably within the Origin X's 60W ceiling

• RTAs built within 0.15 to 2.0ohm, ideal for anyone who prefers building their own coils

• MTL tanks for a tighter, more restricted draw closer to a cigarette

Also compatible:

• RDAs within the same resistance range, for dripping rather than tank vaping

• Tanks over 24mm will overhang the mod slightly and are best avoided

How to Set Up the OXVA Origin X 510 Adaptor

1. Remove the Origin X pod from the device by pulling it free of the magnetic connection.

2. Align the 510 adaptor with the magnetic contacts on the mod and press it into place.

3. Thread your chosen 510 tank or atomiser into the adaptor.

4. Power on the Origin X; it will read the coil resistance automatically.

5. Adjust wattage to suit your coil and begin vaping.

What's in the OXVA Origin X 510 Adaptor Box

Just the adaptor itself, one unit per pack. No coils, no tank, no cable, and no device. You will need your own 510 tank or rebuildable and a charged 18650 already sitting in the Origin X.

Designed Exclusively for the OXVA Origin X

This adaptor is built specifically for the OXVA Origin X Pod Kit and its magnetic connection point. It is not interchangeable with other OXVA devices or third-party pod mods, so it is worth double-checking which Origin you own before ordering.

Once fitted, it supports 510-threaded sub-ohm tanks, MTL tanks, and rebuildable atomisers up to 24mm in diameter.

About OXVA

OXVA built its name on straightforward, well-made pod systems, and the Origin X carries that same approach into a mod that adapts to how you actually want to vape. The brand favours solid magnetic connections, accurate coil reading, and hardware that does not need constant fiddling to work properly.

Its wider range spans everything from beginner-friendly Pod Kits to mods built for sub-ohm and rebuildable setups, and Pirate Vapes carries the range as a genuine, authorised stockist. This adaptor fits that philosophy exactly: one small part that stretches an already capable device further, without asking you to relearn anything about how it runs.

Stock Up and Save

Small accessories like this are easy to lose track of, so it is worth grabbing a spare if you swap tanks often. Every order is packed carefully and sent out on a tracked service, so it arrives in one piece and on time.

Checkout at Pirate Vapes is age-verified throughout, 18+ only, in line with UK vaping regulations. Genuine OXVA stock, nothing grey-market, every time.

Conclusion

If you already own the Origin X and want to run a tank it was not built for out of the box, this adaptor is the cheapest way to get there.

It keeps the magnetic fit you are used to, adds a proper 510 thread, and does not touch the mod's performance in the process. Browse the full OXVA Origin X Pod Kit range and other vape accessories at Pirate Vapes to build out your setup.

FAQs

Will it work with other OXVA devices?

No. This adaptor is made specifically for the Origin X and its magnetic connection point. It will not fit other OXVA pod kits or third-party mods.

What size tank can I fit?

Up to 24mm without overhang. A 22mm tank sits flush, and anything wider than 24mm will extend past the mod's deck slightly.

Does fitting it change how the mod performs?

Not in any meaningful way. The gold-plated contacts keep the connection clean, and the chipset reads the coil and runs exactly as it would with the stock pod.

Is there any wobble once a tank is fitted?

Some minor movement is normal with any magnetic connection. It is secure enough for daily use, though it will not feel quite as rigid as a fully threaded mod top.

Can I run an RDA or RTA with this?

Yes, as long as the build sits within 0.15 to 2.0ohm and the atomiser is 24mm or under in diameter.

Does it come with anything else?

Just the adaptor. One unit per pack, no tank, coil, or cable included.