Vaporesso Gen Fit Kit

Vaporesso Gen Fit Kit

A one-button MTL kit that also fires on the draw. The Vaporesso Gen Fit pairs a 1200mAh built-in battery with the iTank M and a pre-fitted 1.2ohm MTX coil, tuned for a tight mouth-to-lung draw rather than big clouds. Output runs 5 to 20W across three power levels, and Pulse Mode keeps the flavour steady from the first pull to the last.

You can vape it by pressing the button or simply by inhaling. Small, light and easy to run, it suits new vapers and anyone after a fuss-free MTL setup. Browse the wider Vaporesso Range for coils and spares.

Why vapers choose this:

• It fires two ways. Press the button or just inhale, since the Gen Fit has both a fire button and a draw sensor, so you vape however feels natural without changing a setting.

• Pulse Mode holds the flavour by pulsing power rather than letting it sag as the battery drops.

• Three power levels, set with a triple click. No screen, no menu.

• Tiny and light. It disappears in a pocket.

• The iTank M refills from the top and has an adjustable airflow ring, so you tune the draw to taste.

Vaporesso Gen Fit Features

Fire It Two Ways

Most starter kits make you choose between a button or an auto-draw. The Gen Fit gives you both. A draw sensor fires the coil when you inhale, and the side fire button works if you would rather trigger it yourself. New vapers tend to start on draw activation and move to the button later. Either way, there is nothing to set up.

Why Bother With Pulse Mode?

Pulse Mode is a feature Vaporesso usually reserves for its bigger mods. Instead of a flat output, the AXON chip pulses power to the coil, which keeps the hit and the flavour consistent even as the 1200mAh battery runs down. In a small MTL kit, that means your last vape of the day tastes much like your first.

Three Power Levels, No Menu to Learn

There is no screen to read here. Press the fire button three times, and the Gen Fit steps through High, Medium, and Low, shown by three small LEDs on the side. Match the level to your Nic Salts and your taste: lower for a cooler, tighter draw, higher for a little more warmth. That is the entire control system.

The iTank M Does the Heavy Lifting

The included iTank M is a compact 2ml MTL tank in stainless steel. It fills from the top through a single port, the 1.2ohm MTX coil presses straight in, and an airflow ring at the base tightens or opens the draw. Pick up spare Vaporesso MTX Coils so a worn coil never leaves you stuck mid-vape.

Small, Light, Pocketable

At 74.3mm tall, the mod is barely bigger than the tank sitting on top of it. It slips into a jacket pocket or a small bag and weighs next to nothing, which is the whole idea of a kit built to go everywhere. Not much else to say. It is a proper carry-anywhere vape.

Vaporesso Gen Fit Colours

Six finishes are stocked, all on the same compact body. The hardware is identical, so choose on looks alone.

#buttons

• Midnight Black
• Navy Blue
• Pink
• Rose Gold
• Sierra Blue
• Space Grey

How to Set Up the Vaporesso Gen Fit

New coil or first fill, the routine is the same. A couple of minutes.

1. Twist the base off the iTank M and pull out the old MTX coil if you are swapping one.

2. Trickle a few drops of e-liquid straight into the coil's side holes, then dab one more onto the top cotton so nothing starts dry.

3. Press the primed coil firmly into the tank base until it clicks home, then screw the base back on.

4. Open the top cap and fill the tank with your 50/50 or nic salt liquid, keeping clear of the central airflow tube.

5. Leave the filled tank standing for a full five minutes so the cotton wicks through completely.

6. Charge over Type-C, set the power to Low to begin, and draw or press to vape.

What's in the Vaporesso Gen Fit Box

The kit comes with:

• The Gen Fit mod,

• the iTank M at 2ml,

• a pre-installed 1.2ohm MTX coil,

• a Type-C charging cable,

• a user manual,

• and a warranty card.

There is no e-liquid included, so add a bottle to get going. A spare coil or two is worth grabbing at the same time.

Runs the MTX Coil Series in the iTank M

The Gen Fit's tank is built around Vaporesso's MTX coil platform, with the 1.2ohm head fitted from the box for classic MTL vaping at low power. Coils press in and pull out with no threading, so swaps take seconds, and Pirate Vapes keeps the MTX heads in stock for when one wears out. If you settle on a coil you like, it is worth putting it on The Crow's Nest auto refill so you never run dry.

The mod uses a 510 thread, so it can take other 510 tanks too, though the kit is tuned to run best with the iTank M it ships with. For a similar mouth-to-lung feel, browse other MTL Tanks if you want to try a different one later.

About Vaporesso

The Gen Fit is Vaporesso's MTL entry into the Gen line, a range better known for larger sub-ohm mods like the Gen 200. Here the brand shrank that engineering down: the AXON chip and its Pulse Mode come straight from the bigger devices, paired with the new MTX coil system for a tight, flavour-first draw.

Vaporesso is one of the largest names in vape hardware, and building a simple MTL kit around proven parts is a big reason the Gen Fit stays reliable and easy to keep in coils.

Stock Up and Save

An MTL coil is a consumable, so a spare pack of MTX coils and a bottle of your usual liquid keep the Gen Fit running without a gap. Pirate Vapes dispatches every order the same day when it is placed before 4 pm, packed to arrive safely.

All stock is TPD compliant, sold through an age-verified checkout to over-18s only, with Free Pirate Post on orders over £40.

Conclusion

The Gen Fit is a small, honest MTL kit: a 1.2ohm MTX coil, three power levels, Pulse Mode for steady flavour, and firing by draw or button. It suits new vapers and anyone who wants a tidy mouth-to-lung setup without menus or clouds.

Fill it, set it low, and vape. Grab the Gen Fit, spare coils, and any Vape Accessories you need from Pirate Vapes.

FAQs

Is the Gen Fit MTL or DTL?

MTL. It is a mouth-to-lung kit with a 1.2ohm coil and low power, so the draw is tight and cigarette-like, not an airy cloud vape.

What e-liquid should I use in the Gen Fit?

A 50/50 or a nic salt at a higher strength suits the MTL coil best. High-VG cloud juice is too thick for it and will not wick well.

How do I change the power in the Gen Fit?

Press the fire button three times to step through High, Medium and Low. Three side LEDs show the level.

How long does an MTX coil last?

Usually one to two weeks with daily use. Sweeter liquids clog the coil faster, so a fruit or menthol juice tends to stretch it further.

Draw or button, which is better?

Whichever you prefer. Draw activation is the simplest for a new vaper. The button gives you a little more control over when it fires.

How big is the Gen Fit tank?

2ml, filled from the top. That is the UK TPD size, and the iTank M is a compact stainless-steel MTL tank.